TÜBİTAK UME CALIBRATION / TEST LIST
ACOUSTICS & VIBRATION LABORATORY CALIBRATION / TEST LIST
CODE |
NAME |
NOTE |
G2AK-1100 |
Reciprocity Calibration of 1" Standard Reference Microphones (10 Hz - 10 kHz frekans aralığındaki 1/3 Oktav Bant Merkez Frekanslarında) |
|
G2AK-1200 |
Reciprocity Calibration of ½ " Standard Reference Microphones
(Calibration at 1/3 octave band center frequencies in the range from 10 Hz to - 25 kHz) |
|
G2AK-1500 |
Comparison Calibration of Condenser Microphones and Determination of Frequency Response (Determination of absolute sensitivity at frequency of 250 Hz and frequency response by electrostatic actuator.) |
|
G2AK-1600 |
Determination of Free Field Response of Condenser Microphone by Comparision Method (Calibration at 1/3 octave band center frequencies in the frequency range 1 kHz to 16 kHz) |
|
G2AK-2100 |
Calibration of Sound Level Calibrator |
|
G2AK-2300 |
Calibration of Pistonphone within Sound Intensity Set |
|
G2AK-2400 |
Calibration of Multifunction Acoustical Calibrator |
|
G2AK-3100 |
Calibration of Sound Level Meter (Acoustical Tests) |
6 |
G2AK-3110 |
Calibration of Sound Level Meter (Acoustical and Electrical Tests) |
6 |
G2AK-3150 |
Determination of Free Field Response of Sound Level Meter (Calibration at 1/3 octave band center frequencies in the frequency range 1 kHz to 16 kHz) |
|
G2AK-3200 |
Calibration of Noise Dose Meter |
|
G2AK-3500 |
Calibration of Pure Tone Audiometer |
|
G2AK-3600 |
Calibration of Hearing Aid Analyzer |
|
G2AK-3700 |
Calibration of Artificial Ear |
|
G2AK-3800 |
Calibration of Artificial Mastoid |
|
G2AK-3900 |
Calibration of Ear Simulator |
|
G2AK-4300 |
Sound Power/Intensity Measurement |
1,2,4,5 |
G2AK-4310 |
Sound Pressure/Power Measurement in Special Acoustical Rooms |
1,2,5 |
G2AK-4400 |
Calibration of Reference Sound Source ( ISO 6926) |
|
G2AK-5100 |
Determination of Acoustical Properties of Materials |
1,2,5 |
G2AK-6100 |
Reverberation Time Measurement |
2,4 |
G2AK-6210 |
Daily Use of Full/Semi Anechoic Room / (8 Hours) |
3 |
G2AK-6220 |
Daily Use of Reverberation Room / (8 Hours) |
3 |
G2AK-7100 |
Calibration of Microphone Preamplifier (Calibration at 1/3 octave band center frequencies in the frequency range 20 Hz to 25 kHz) |
|
G2AK-7200 |
Calibration of Signal Contioner (Calibration at 1/3 octave band center frequencies in the frequency range 20 Hz to 25 kHz) |
|
G2AK-9900 |
Special Calibration / Test |
2,4,5 |
(1) |
Accredited Service |
(2) |
Cost of the service is determined based on your request. |
(3) |
Equipment belongs to the customer is used for this service |
(4) |
Accommodation and transportation costs will be added to the measurement cost |
(5) |
|
(6) |
|
AIR VELOCITY MEASUREMENTS LABORATORY CALIBRATION / TEST LIST
CODE |
NAME |
NOTE |
G2AH-0900 |
Micro Anemometer 0.5-40 m/s Anemometer Calibrations by Static Pitot Tube |
1,2,3,5 |
G2AH-9900 |
Specific Anemometer Measurements |
4,5 |
(1) |
Acredited item. |
(2) |
|
(3) |
|
(4) |
Price depends on type of test and type of device. |
(5) |
|
ANGLE MEASUREMENTS LABORATORY CALIBRATION / TEST LIST
CODE |
NAME |
NOTE |
G2BC-1100 |
Autocollimator |
1, 3 |
G2BC-1200 |
Electronic Level (per couple) |
1 |
G2BC-1600 |
Clinometer |
1 |
G2BC-2100 |
Angular Gauge Blocks (per piece) |
1, 2, 3 |
G2BC-2200 |
True Square |
1 |
G2BC-2300 |
Optical Polygon (price for each measuring surface) |
1 |
G2BC-2500 |
Index Table (with 30° increments) |
1, 4 |
G2BC-3000 |
Adjustable Reference Mirror with one face |
1 |
G2BC-3100 |
Adjustable Reference Mirror with double face |
1 |
G2BC-3200 |
Magnetic Back Mirror |
1 |
G2BC-3300 |
Rotary Table |
1, 3 |
G2BC-3400 |
Small Angle Generator |
|
G2BC-9900 |
Special Calibration / Test |
3 |
(1) |
Accredited Item. |
(2) |
Valid for 90° Angle gauge blocks in form of True Square |
(3) |
Price quoted will be determined acc. to request. Prices differ depending on the service. Given price is the lowest calibration price |
(4) |
|
() |
|
BIOANALYSIS LABORATORY CALIBRATION / TEST LIST
CODE |
NAME |
NOTE |
G3BA-1100 |
|
1 |
G3BA-1110 |
Relative quantification of GMO DNA (MON810) in seeds - Real Time PCR Instrument |
1 |
G3BA-1120 |
Relative quantification of GMO DNA (Bt63) in seeds - Real Time PCR Instrument |
1 |
G3BA-1210 |
Relative quantification of GMO DNA (MON810) in seeds - Digital PCR Instrument |
1 |
G3BA-1220 |
Relative quantification of GMO DNA (Bt63) in seeds - Digital PCR Instrument |
1 |
G3BA-1230 |
Relative quantification of GMO DNA (DP-Ø73496-4/RT73) in seeds - Digital PCR Instrument |
1 |
G3BA-1310 |
Meat Authentication, Qualitative Analysis (Beef) - Digital PCR Instrument |
1 |
G3BA-1320 |
Meat Authentication, Qualitative Analysis (Pork) - Digital PCR Instrument |
1 |
G3BA-1330 |
Meat Authentication, Qualitative Analysis (Horse) - Digital PCR Instrument |
1 |
G3BA-1340 |
Meat Authentication, Qualitative Analysis (Camel) - Digital PCR Instrument |
1 |
G3BA-1350 |
Meat Authentication, Qualitative Analysis (Sheep) - Digital PCR Instrument |
1 |
G3BA-1360 |
Meat Authentication, Qualitative Analysis (Goat) - Digital PCR Instrument |
|
G3BA-1370 |
Meat Authentication, Qualitative Analysis (Chicken) - Digital PCR Instrument |
|
G3BA-1380 |
Meat Authentication, Qualitative Analysis (Duck) - Digital PCR Instrument |
1 |
G3BA-1390 |
Meat Authentication, Qualitative Analysis (Salmon) - Digital PCR Instrument |
1 |
G3BA-1410 |
Meat Authentication, Quanitative Analysis (Beef) - Digital PCR Instrument |
1 |
G3BA-1420 |
Meat Authentication, Quantitative Analysis (Pork) - Digital PCR Instrument |
|
G3BA-1430 |
Meat Authentication, Quantitative Analysis (Horse) - Digital PCR Instrument |
1 |
G3BA-1440 |
Meat Authentication, Quantitative Analysis (Camel) - Digital PCR Instrument |
1 |
G3BA-1450 |
Meat Authentication, Quantitative Analysis (Sheep) - Digital PCR Instrument |
1 |
G3BA-1460 |
Meat Authentication, Quantitative Analysis (Goat) - Digital PCR Instrument |
1 |
G3BA-1470 |
Meat Authentication, Quantitative Analysis (Chicken) - Digital PCR Instrument |
1 |
G3BA-1480 |
Meat Authentication, Quantitative Analysis (Duck) - Digital PCR Instrument |
1 |
G3BA-1490 |
Meat Authentication, Quantitative Analysis (Salmon) - Digital PCR Instrument |
1 |
G3BA-1610 |
|
1 |
G3BA-1620 |
|
1 |
G3BA-1630 |
|
1 |
G3BA-1640 |
|
1 |
G3BA-2100 |
Relative quantification of RNA transcripts - Real Time PCR Instrument |
1, 3 |
G3BA-3100 |
Relative quantification of DNA methylation levels - Real Time PCR Instrument Melting Analysis |
1, 3 |
G3BA-3200 |
|
1, 3 |
G3BA-4100 |
Absolute quantification of plasmid DNA - Digital PCR Instrument |
1, 3 |
G3BA-4210 |
Relative quantification of oncogenes (KRAS-G12D) - Digital PCR Instrument |
1, 4 |
G3BA-4220 |
Relative quantification of oncogenes (BRAF-V600E) - Digital PCR Instrument |
1,4 |
G3BA-4230 |
Relative quantification of oncogenes (EGFR-?746-750) - Digital PCR Instrument |
1, 4 |
G3BA-4310 |
Absolute quantification of HIV virus - Digital PCR Instrument |
1, 4 |
G3BA-4320 |
Absolute quantification of SARS-CoV-2 virus - Digital PCR Instrument |
1,3,4 |
G3BA-5100 |
Amino acid analysis for pure protein/peptide - LC-ID-MS |
1 |
G3BA-5300 |
Quantification of C-peptide/angiotensin - LC-ID-MS(n) |
1 |
G3BA-5400 |
Quantification of protein concentration - HPLC |
1 |
G3BA-5500 |
Quantification of protein concentration - ELISA |
1 |
G3BA-5600 |
Quantification of protein/peptide concentration - PICAA Analysis |
1 |
G3BA-5700 |
Relative quantification of HbA1c protein - HPLC |
1 |
G3BA-5800 |
Relative quantification of HbA1c protein - LC-ID-MS |
1 |
G3BA-5900 |
Determination of amylase enzyme activity - Spectrophotometric |
1 |
G3BA-6000 |
Complex Proteome Analysis - Relative Quantification (LFQ-TMT) |
1 |
G3BA-6100 |
Identification of Post Translational Modifications ( Methylation, Acetylation, Phosphorylation etc.) |
1 |
G3BA-6200 |
Peptide Fragmentation (HCD) |
1 |
G3BA-6300 |
LC-MS/MS Method based protein identification |
1 |
G3BA-9900 |
Special Calibration / Test |
2 |
(1) |
Pricing is for one sample, please inquire pricing for more than two samples |
(2) |
Price depends on the requirements. |
(3) |
|
(4) |
|
CAPACITANCE LABORATORY CALIBRATION / TEST LIST
CODE |
NAME |
NOTE |
G1KA-1100 |
Standard Capacitance Calibration (1 kHz) |
1, 2 |
G1KA-1150 |
|
2 |
G1KA-1200 |
Standard Capacitance Calibration (50 Hz - 20 kHz) (for 5 frequency point) |
1, 2 |
G1KA-1300 |
Standard Capacitance Calibration (1 kHz – 30 MHz) (for 15 frequency point) |
1, 2 |
G1KA-1400 |
Capacitance Bridge Calibration |
1 |
G1KA-1600 |
Calibration of multifunction calibrator (capacitance part ) |
1 |
G1KA-1700 |
|
|
G1KA-2100 |
Standard Inductance Calibration |
1, 4 |
G1KA-3100 |
AC Resistance Calibration |
1, 2 |
G1KA-3300 |
Impedance Calibration (Frequency < 110 MHz) |
5, 6 |
G1KA-3310 |
|
5, 6, 7 |
G1KA-4200 |
RLC Meter Calibration |
1 |
G1KA-5100 |
AC1 Artificial Cable Calibration |
1 |
G1KA-5500 |
Cable Test Devices Calibration |
|
G1KA-5700 |
AC Null Dedector Calibration |
|
G1KA-6300 |
IVD Calibration (1 kHz) |
1, 8 |
G1KA-7000 |
Strain Gauge Indicator Calibration (For each channel) |
|
G1KA-9900 |
Special Calibration / Test |
3 |
(1) |
Accredited Item. |
(2) |
If more frequency points are requested, 330 TL is added for each extra frequency point to the price. |
(3) |
Price depends on the requirements. |
(4) |
|
(5) |
|
(6) |
|
(7) |
|
(8) |
|
CONTACT THERMOMETRY LABORATORY CALIBRATION / TEST LIST
CODE |
NAME |
NOTE |
G1KS-0100 |
Comparisons of Fixed Point Cells |
1, 2, 4 |
G1KS-0110 |
Comparison of Argon Cell |
1, 2, 4 |
G1KS-0120 |
Comparison of Mercury Cell |
1, 2, 4 |
G1KS-0130 |
Comparison of Gallium Cell |
1, 2, 4 |
G1KS-0140 |
Comparison of Indium Cell |
1, 2, 4 |
G1KS-0150 |
Comparison of Tin Cell |
1, 2, 4 |
G1KS-0160 |
Comparison of Zinc Cell |
1, 2, 4 |
G1KS-0170 |
Comparison of Aluminum Cell |
1, 2, 4 |
G1KS-0180 |
Comparison of Silver Cell |
1, 2, 4 |
G1KS-0200 |
-189.3442 °C / +29.7646 °C Resistance Thermometer (SPRT, HTPRT) Calibration at Fixed Point Defined by ITS 90 |
1, 2, 4, 5 |
G1KS-0210 |
-189.3442 °C / +156.5985 °C Resistance Thermometer (SPRT, HTPRT) Calibration at Fixed Point Defined by ITS 90 |
1, 2, 4, 5 |
G1KS-0220 |
-189.3442 °C / +231.928 °C Resistance Thermometer (SPRT, HTPRT) Calibration at Fixed Point Defined by ITS 90 |
1, 2, 4, 5 |
G1KS-0230 |
-189.3442 °C / +419.527 °C Resistance Thermometer (SPRT, HTPRT) Calibration at Fixed Point Defined by ITS 90 |
1, 2, 4, 5 |
G1KS-0240 |
-189.3442 °C / +660.323 °C Resistance Thermometer (SPRT, HTPRT) Calibration at Fixed Point Defined by ITS 90 |
1, 2, 4, 5 |
G1KS-0250 |
-38.8344 °C / +29.7646 °C Resistance Thermometer (SPRT, HTPRT) Calibration at Fixed Point Defined by ITS 90 |
1, 2, 4, 5 |
G1KS-0260 |
-38.8344 °C / +156.5985 °C Resistance Thermometer (SPRT, HTPRT) Calibration at Fixed Point Defined by ITS 90 |
1, 2, 4, 5 |
G1KS-0270 |
-38.8344 °C / +231.928 °C Resistance Thermometer (SPRT, HTPRT) Calibration at Fixed Point Defined by ITS 90 |
1, 2, 4, 5 |
G1KS-0280 |
-38.8344 °C / +419.527 °C Resistance Thermometer (SPRT, HTPRT) Calibration at Fixed Point Defined by ITS 90 |
1, 2, 4, 5 |
G1KS-0290 |
-38.8344 °C / +660.323 °C Resistance Thermometer (SPRT, HTPRT) Calibration at Fixed Point Defined by ITS 90 |
1, 2, 4, 5 |
G1KS-0300 |
0.01 °C / +156.5985 °C Resistance Thermometer (SPRT, HTPRT) Calibration at Fixed Point Defined by ITS 90 |
1, 2, 4, 5 |
G1KS-0310 |
0.01 °C / +231.928 °C Resistance Thermometer (SPRT, HTPRT) Calibration at Fixed Point Defined by ITS 90 |
1, 2, 4, 5 |
G1KS-0320 |
0.01 °C / +419.527 °C Resistance Thermometer (SPRT, HTPRT) Calibration at Fixed Point Defined by ITS 90 |
1, 2, 4, 5 |
G1KS-0330 |
0.01 °C / +660.323 °C Resistance Thermometer (SPRT, HTPRT) Calibration at Fixed Point Defined by ITS 90 |
1, 2, 4, 5 |
G1KS-0340 |
0.01 °C / +961.78 °C Resistance Thermometer (SPRT, HTPRT) Calibration at Fixed Point Defined by ITS 90 |
1, 2, 4, 5 |
G1KS-0350 |
0.01 °C / +29.7646 °C Resistance Thermometer (SPRT, HTPRT) Calibration at Fixed Point Defined by ITS 90 |
1, 2, 4, 5 |
G1KS-0370 |
0.01 °C / 1084 °C Resistance Thermometer (SPRT, HTPRT) Calibration at Fixed Point Defined by ITS 90 |
1, 2, 4, 8 |
G1KS-0380 |
419.527 °C / 1324 °C |
|
G1KS-0490 |
-196 °C / 0 °C Calibration of Resistance/ Digital Thermometer (Pt-100, Intelligent Prob, thermistor etc) by comparison method |
1, 2, 4, 6 |
G1KS-0495 |
-80 °C / 0 °C Calibration of Resistance/ Digital Thermometer (Pt-100, Intelligent Prob, thermistor etc) by comparison method |
1, 2, 4, 6 |
G1KS-0500 |
-80 °C / +85 °C Calibration of Resistance/ Digital Thermometer (Pt-100, Intelligent Prob, thermistor etc) by comparison method |
1, 2, 4, 6 |
G1KS-0510 |
-80 °C / +250 °C Calibration of Resistance/ Digital Thermometer (Pt-100, Intelligent Prob, thermistor etc) by comparison method |
1, 2, 4, 8 |
G1KS-0520 |
-80 °C / +550 °C Calibration of Resistance/ Digital Thermometer (Pt-100, Intelligent Prob, thermistor etc) by comparison method |
1, 2, 4, 9 |
G1KS-0530 |
0 °C / +85 °C Calibration of Resistance/ Digital Thermometer (Pt-100, Intelligent Prob, thermistor etc) by comparison method |
1, 2, 4, 6 |
G1KS-0540 |
0 °C / +250 °C Calibration of Resistance/ Digital Thermometer (Pt-100, Intelligent Prob, thermistor etc) by comparison method |
1, 2, 4, 8 |
G1KS-0550 |
0 °C / +550 °C Calibration of Resistance/ Digital Thermometer (Pt-100, Intelligent Prob, thermistor etc) by comparison method |
1, 2, 4, 8 |
G1KS-0560 |
-80 °C / +650 °C |
1, 2, 4, 9 |
G1KS-0570 |
-196 °C / +550 °C Calibration of Resistance/ Digital Thermometer (Pt-100, Intelligent Prob, thermistor etc) by comparison method |
1, 2, 4, 9 |
G1KS-0580 |
|
1, 2, 4, 9 |
G1KS-0850 |
600 °C/ 1100 °C Calibration of Thermocouples and Digital Thermometers by Comparison Method |
1, 2, 3, 4, 6 |
G1KS-0870 |
600 °C / 1300 °C Calibration of Thermocouples and Digital Thermometers by Comparison Method |
1, 2, 3, 4, 6 |
G1KS-0890 |
|
|
G1KS-0910 |
Calibration of Temperature-Controlled Volumes for one temperature calibration points |
7 |
G1KS-0915 |
|
7 |
G1KS-0920 |
-40 °C / 420 °C |
1, 6 |
G1KS-0930 |
|
1, 6 |
G1KS-9900 |
Special Calibration / Test |
2, 5 |
G1KS-9910 |
|
|
(1) |
Acredited Calibration. |
(2) |
Please specify the calibration temperature range, thermometer diameter, immersion depth in the calibration request form and send all relevant documents (manuals, certificates etc) |
(3) |
As a calibration acceptance criteria; the maximum diameter of the platinum based thermocouples should be 7 mm and its protection tube should be of very clean ceramic material. |
(4) |
Please note that laboratory will not be held responsible for any damages occurring to the equipment during the calibration process and up to 50% of calibration price will be demanded in case the instrument under calibration malfunctions or shows instability. |
(5) |
|
(6) |
Calibration price is determined for up to five calibration points. Additional points will subject to extra price. |
(7) |
Calibration points that should lie within -80 °C and 200 °C should be specified by the customer. |
(8) |
Calibration price is determined for up to seven calibration points. Additional points will subject to extra price. |
(9) |
|
DC VOLTAGE CALIBRATION / TEST LIST
CODE |
NAME |
NOTE |
G1LR-1100 |
Standard Resistance Calibration (0,1 m Ohm <= R <= 100 mOhm) (Only for one current) |
1, 2 |
G1LR-1300 |
Standard Resistance Calibration (100 mOhm < R<=10 kOhm ) (Only for one current) |
1, 2 |
G1LR-1500 |
Standard Resistance Calibration (10 kOhm < R <= 1 GOhm ) (Only for one voltage) |
1, 2, 5 |
G1LR-1700 |
Standard Resistance Calibration (1 GOhm < R 1 TOhm ) (Only for one voltage) |
1, 2 |
G1LR-2300 |
DC Current Shunt Calibration (0-100 A) (Only for one current) |
1,2 |
G1LR-2500 |
DC Current Shunt Calibration 9211A (0-100 A) |
1,6 |
G1LR-4000 |
Precision Resistance Meter |
1 |
G1LR-4700 |
Ohmmeter Calibration |
1, 3 |
G1LR-5100 |
Temperature Coefficient Calculation of Standard Resistances
(1 Ohm - 10 kOhm , Temperature Range 20 °C – 25 °C) |
1 |
G1LR-7100 |
Surface and Volume Resistivity Measurement |
|
G1LR-7200 |
Surface Resistivity Measurement |
|
G1LR-7300 |
Volume Resistivity Measurement |
|
G1LR-7600 |
Contact Resistance Experiment |
|
G1LR-7700 |
Isolation Resistance Experiment |
|
G1LR-8100 |
AC Conductivity Measurement Device Calibration |
1, 3 |
G1LR-8200 |
AC Conductivity Standard Calibration ( For each standard) |
1 |
G1LR-9100 |
Low Current Measuring Device Calibration (2 pA – 10 µA) |
1, 3 |
G1LR-9200 |
Low Current Source Calibration (2 pA – 10 µA) |
1, 3 |
G1LR-9900 |
Special Calibration / Test |
4 |
(1) |
Accredited Item. |
(2) |
The half of the calibration price is added to the calibration price for each extra measurement point. |
(3) |
If your instrument works on batteries please provide spare batteries. Please specify explicitly if your instrument works with power supply other than 220 VAC. |
(4) |
Price depends on the requirements. |
(5) |
Maximum measurement voltage is 100 V. |
(6) |
The half of the calibration price of G1LR-2300 is added to the calibration price for each extra current. |
ELECTROCHEMISTRY LABORATORY CALIBRATION / TEST LIST
CODE |
NAME |
NOTE |
G3EK-1401 |
Determination of pH 4 CRM by Primary Level pH Measurement System |
1 |
G3EK-1402 |
Determination of pH 7 CRM by Primary Level pH Measurement System |
1 |
G3EK-1403 |
Determination of pH 10 CRM by Primary Level pH Measurement System |
1 |
G3EK-1404 |
Determination of Conductivity by Primary Level Conductivity Measurement System |
1 |
G3EK-1450 |
Cyclic Voltammetric (CV) Measurements |
1 |
G3EK-9900 |
Special Calibration / Test |
1 |
(1) |
Price depends on the requirements |
ELECTROMAGNETIC RADIATION LABORATORY CALIBRATION / TEST LIST
CODE |
NAME |
NOTE |
G1ER-0100 |
It is called "electrical bursts (electrical fast transients)" in type tests.
|
1, 2, 19, 21 |
G1ER-0200 |
Conducted Emission (Use of Absorbing Clamp) |
1, 2, 19, 21 |
G1ER-0300 |
Conducted Emission (Use of DIA) |
1, 2, 19, 21 |
G1ER-0400 |
Conducted Emission (Use of Current Probe) |
1, 2, 19, 21 |
G1ER-0500 |
Conducted Emission (Use of Voltage Probe) |
1, 2, 19, 21 |
G1ER-0600 |
Conducted Emission (Harmonics) |
1, 2, 19, 21 |
G1ER-0700 |
Conducted Emission (Flicker) |
1, 2, 19, 21 |
G1ER-0800 |
Radiated Emission |
1, 2, 19, 21 |
G1ER-0900 |
Conducted Immunity (Use of CDN) |
1, 2, 19, 21 |
G1ER-0950 |
Conducted Immunity (Use of BCI) |
1, 2, 19, 21 |
G1ER-1000 |
Conducted Immunity (ESD) |
1, 4, 14, 19, 21 |
G1ER-1100 |
Conducted Immunity (EFT) |
1, 2, 15, 19, 21 |
G1ER-1200 |
Conducted Immunity (Surge) |
1, 2, 18, 19, 21 |
G1ER-1300 |
Conducted Immunity (Voltage Dips and Interruptions) |
1, 2, 16, 19, 21 |
G1ER-1350 |
Magnetic Immunity (50 / 60 Hz) |
1, 2, 19, 21 |
G1ER-1400 |
Radiated Immunity (3 V/m - 30 V/m, 26 MHz - 6.5 GHz) |
1, 3, 17, 19, 21 |
G1ER-3230 |
Full EMC Tests of Vehicles and Tractors According To 72/245, 75/322, 95/54 or E.C.E. 10 Directive |
1, 3, 19, 21 |
G1ER-3330 |
EMC Tests of Vehicle/Tractor Sub-Assemblies According To 72/245, 75/322, 95/54 or E.C.E. 10 Directive
|
1, 3, 19, 21 |
G1ER-3600 |
RE101, Magnetic Field, 30 Hz - 100 kHz |
1, 2, 4, 19, 21 |
G1ER-3700 |
RE102, Electric Field (10 kHz –- 18 GHz) |
1, 3, 4, 19, 21 |
G1ER-3900 |
CE101, Power Leads, 30 Hz - 10 kHz (single phase) |
1, 2, 19, 21 |
G1ER-4000 |
CE102, Power Leads, 10 kHz - 10 MHz (single phase) |
1, 2, 19, 21 |
G1ER-4200 |
RS101, Magnetic Field, 30 Hz - 100 kHz |
1, 2, 4, 6, 11,19, 21 |
G1ER-4300 |
RS103, Electric Field, 2 MHz - 18 GHz, 10 V/m - 200 V/m, EUT Surface up to 900 cm²
|
1, 3, 5, 6, 7, 10, 19, 21 |
G1ER-4400 |
CS101, Power Leads, 30 Hz - 150 kHz (single phase) |
1, 2, 6, 11, 19, 21 |
G1ER-4710 |
CS106 Power Leads, (single phase) |
1, 2, 11, 19, 21 |
G1ER-4900 |
CS114, Bulk Cable Injection, 10 kHz - 200 MHz |
1, 2, 6, 11, 19, 21 |
G1ER-5000 |
CS115, Bulk Cable Injection/Impulse Excitation |
1, 2, 11, 19, 21 |
G1ER-5100 |
CS116, Damped Sinusoidal Transients |
1, 2, 11, 19, 21 |
G1ER-5110 |
CS118, Electrostatic Discharge |
1, 4, 19, 21 |
G1ER-5210 |
Active-Passive Rod and Loop Antenna Calibration (Frequency range: 5 Hz - 30 MHz) |
8, 12, 20 |
G1ER-5220 |
Biconical, Bilog, Log-Periodic, Horn Antenna Calibration (Frequency range: 30 MHz - 300 MHz or 200 MHz - 1 GHz) |
8, 12, 13, 20 |
G1ER-5225 |
Bilog / Mini Biconical Antenna Calibration (Frequency range: 30 MHz - 1 GHz)
|
8, 12, 13, 20 |
G1ER-5230 |
Horn Antenna Calibration (Frequency range: 1 GHz - 18 GHz) |
8, 12, 13, 20 |
G1ER-5240 |
Horn Antenna Calibration (Frequency range: 18 GHz - 26,5 GHz) |
8, 12, 13, 20 |
G1ER-5250 |
Horn Antenna Calibration (Frequency range: 26 GHz - 40 GHz) |
8,12,13,20 |
G1ER-5310 |
Electric/Magnetic Field Probe Calibration ( Frequency range: 30 Hz - 32 kHz) |
8, 12, 20 |
G1ER-5320 |
Electric/Magnetic Field Probe Calibration( Frequency range: 30 Hz - 3 MHz) |
8, 12, 20 |
G1ER-5330 |
Electric/Magnetic Field Probe Calibration( Frequency range: 30 Hz - 30 MHz) |
8, 12, 20 |
G1ER-5340 |
Electric/Magnetic Field Probe Calibration( Frequency range: 30 Hz - 3 GHz) |
8, 12, 20 |
G1ER-5350 |
Electric/Magnetic Field Probe Calibration( Frequency range: 30 Hz - 20 GHz) |
8, 12, 20 |
G1ER-5360 |
Electric/Magnetic Field Probe Calibration( Frequency range: 30 Hz - 40 GHz) |
8, 12, 20 |
G1ER-6100 |
Daily Use of Semi Anechoic Chamber (Radiated Immunity / 8 Hours) |
22 |
G1ER-6200 |
Daily Use of Semi Anechoic Chamber (Radiated Emission / 8 Hours) |
22 |
G1ER-6300 |
Daily Use of Screened Room (Conducted Emission-Immunity / 8 Hours) |
22 |
G1ER-6400 |
Absorbing Clamp Calibration |
8, 20 |
G1ER-6510 |
Voltage/Current Probe Calibration (Frequency range for voltage probes: 150 kHz - 30 MHz, Frequency range for current probes: 30 Hz - 500 MHz, measuring range (-30 dBs) - (70 dBs)) |
8, 20 |
G1ER-9900 |
Special Calibration / Test |
9 |
(1) |
Accredited Service
|
(2) |
30% of the test fee will be added to the total test fee for each additional operating mode and/or each additional port/phase.
|
(3) |
50% of the test fee will be added to the total test fee for each additional operating mode.
|
(4) |
10% of the test fee will be added to the total test fee for each additional application point.
|
(5) |
30% of the test fee will be added to the total test fee for each additional 900 cm2 area of the EUT surface.
|
(6) |
The stated fee is valid for a dwell time up of 6 s maximum. %50 of the test fee will be added to the total test fee for each additional time period of 6 s.
|
(7) |
50% of the test fee will be added to the total test fee for the frequency range of 18 GHz –- 40 GHz.
|
(8) |
50% of the calibration fee will be charged if the equipment under calibration is found to be defective.
|
(9) |
The test/calibration fee is determined in accordance with the tests/calibrations to be performed.
|
(10) |
If determination of a threshold value is requested, it will be charged extra in the scope of Daily Use of Semi Anechoic Chamber (Radiated Immunity)
|
(11) |
If determination of a threshold value is requested, it will be charged extra in the scope of Daily Use of Screened Room (Conducted Emission-Immunity)
|
(12) |
The calibration frequency range is determined as per manufacturer specifications.
|
(13) |
Horn antenna measurements will be performed in the vertical polarization. The other antenna measurements will be performed in the horizontal polarization.
|
(14) |
It is called "electrostatic discharges" in type tests.
|
(15) |
It is called "electrical bursts (electrical fast transients)" in type tests.
|
(16) |
It is called "voltage variations, short time power reductions, voltage dips and short interruptions" in type tests.
|
(17) |
It is called "radiated immunity or immunity to radiated electromagnetic fields" in type tests.
|
(18) |
It is called "surges" in type tests.
|
(19) |
If you accept our offer, 15% of the total test fee must be paid in advance within 5 business days in order to reserve the specified dates for you. In order to provide the requested service, the remaining balance must be deposited in advance and the payment receipt must be sent to our institute at least 5 days before the service date. For tests cancelled up to 30 days before the service date, 15% of the previously paid amount will not be refunded and it will be invoiced and the remaining balance will be returned to you, if any. If the requested services are not cancelled in writing until 30 days in advance, 25% of the total test fee will be invoiced. If the customer does not come for testing on the specified date and postpone the tests, the daily room usage fee for radiated emission tests in our Industrial Services Catalogue will apply.
|
(20) |
The calibration fee is valid for TÜBİTAK UME's standard calibration frequencies. Additional measurement frequencies, if requested, may be charged separately.
|
(21) |
|
(22) |
|
FIBER OPTICS LABORATORY CALIBRATION / TEST LIST
CODE |
NAME |
NOTE |
G1FO-8100 |
Fiber Optic Power (Power Meter), (1310 nm and 1550 nm) |
1 |
G1FO-8200 |
Fiber Optic Attenuator, (1310 nm and 1550 nm) |
1 |
G1FO-8500 |
OTDR (Distance and Attenuation Axes), (1310 nm and 1550 nm) |
1 |
G1FO-9900 |
Special Calibration / Test |
2 |
(1) |
For single mode FC/PC connector |
(2) |
The price will be evaluated with respect to the measurement conditions or customer request. |
FORCE LABORATORY CALIBRATION / TEST LIST
CODE |
NAME |
NOTE |
G2KV-1100 |
Up to 10 kN / Tension Type Force Transducers |
1,2 |
G2KV-1300 |
Up to 100 kN / Tension Type Force Transducers |
1,2 |
G2KV-1500 |
Up to 3 MN / Tension Type Force Transducers |
1,2 |
G2KV-2100 |
Up to 10 kN / Compression Type Force Transducers |
1,2 |
G2KV-2300 |
Up to 100 kN / Compression Type Force Transducers |
1,2 |
G2KV-2500 |
Up to 3 MN / Compression Type Force Transducers |
1,2 |
G2KV-3100 |
Up to 10 kN / Tension and Compression Type Force Transducers |
1,2 |
G2KV-3300 |
Up to 100 kN / Tension and Compression Type Force Transducers |
1,2 |
G2KV-3500 |
Up to 3 MN / Tension and Compression Type Force Transducers |
1,2 |
G2KV-4100 |
Hand Type Force Measuring Devices (Force Gages) |
1, 2 |
G2KV-4200 |
Dynamic Calibration of Force Measuring Devices |
2, 5 |
G2KV-4300 |
Calibration of 4-Channel Force Measuring Devices |
1,2,4 |
G2KV-9900 |
Special Calibration / Test |
3 |
(1) |
The service is in the acrreditation scope. |
(2) |
The calibration of the force transducer is performed at 10% to 100% of the device capacity. Measurements outside this range will be charged extra. |
(3) |
The customer will be responsible for travel and accommodation costs for on-site services. |
(4) |
Includes additional measurements according to EN 12390-4. |
(5) |
|
GAS FLOW LABORATORY CALIBRATION / TEST LIST
CODE |
NAME |
NOTE |
G2AG-3100 |
0 - G4 (0 - 6 m3/h ) Gas Flowmeters |
1,2,5 |
G2AG-3200 |
Sonic Nozzles (0 - 10 m3/h) |
1 |
G2AG-3300 |
G4 - G40 (upto 65 m3/h) Gas Flowmeters |
1,2,5 |
G2AG-3900 |
G1000 - G1600 (upto 2500 m3/h) Gas Flowmeters |
1,2,5 |
G2AG-4300 |
G4000 – G10000 Gas Flowmeters |
1,2,5 |
G2AG-4700 |
On-site calibrations |
2,3,5 |
G2AG-4800 |
Gas Flowmeters Verfcation Tests (for 3 flowrates) |
4,5 |
G2AG-5000 |
Tests Explained in Gas Flowmeter Type Approval Regulations |
4,5 |
G2AG-5200 |
Vane Tests |
4,5 |
G2AG-5400 |
Tests for Gas Armatures |
4,5 |
G2AG-5600 |
Aspirator / Ventilator Tests |
4,5 |
G2AG-9900 |
Specific Gas Flow Calibration / Tests |
4,5 |
(1) |
Acredited item. |
(2) |
Calibration price changes by %50 if more then one meter output calibration is requested, if it is decided that device sent for calibration is not working properly, %50 of the normal price is requested, and if the device is not clean enough for calibration, %50 of the price will also be requsted for cleaning purposes from the customer. |
(3) |
On-Site calibration price is twice the price of calibration at UME and it may increase if there is any by other needs for calibration on-site. Travelling expenses will be added to the price. |
(4) |
Price may change according to device type and tests. |
(5) |
|
GAS METROLOGY LABORATORIES CALIBRATION / TEST LIST
CODE |
NAME |
NOTE |
G3GA-1100 |
Determination of Carbondioxide in Nitrogen (Range: 1-20 % CO2 in N2) |
|
G3GA-1101 |
Determination of Carbondioxide in Nitrogen (Range: 0.1-1 % CO2 in N2) |
|
G3GA-1102 |
Determination of Carbondioxide in Nitrogen (Range: 100-1000 ppm CO2) |
|
G3GA-1103 |
Determination of Carbondioxide in Nitrogen (Range: 10-100 ppm CO2) |
|
G3GA-1110 |
Determination of Carbondioxide in Air (Range: 1-20 % CO2) |
|
G3GA-1111 |
Determination of Carbondioxide in Air (Range: 0.1-1 % CO2) |
|
G3GA-1112 |
Determination of Carbondioxide in Air (Range: 100-1000 ppm CO2) |
|
G3GA-1113 |
Determination of Carbondioxide in Air (Range: 10-100 ppm CO2) |
|
G3GA-1200 |
Determination of Carbonmonoxide in Nitrogen (Range: 0.1-10 % ppm CO) |
|
G3GA-1201 |
Determination of Carbonmonoxide in Nitrogen (Range: 100-1000 ppm CO) |
|
G3GA-1202 |
Determination of Carbonmonoxide in Nitrogen (Range: 10-100 ppm CO) |
|
G3GA-1203 |
Determination of Carbonmonoxide in Nitrogen (Range: 1-10 ppm CO) |
|
G3GA-1204 |
Determination of Carbonmonoxide in Nitrogen (Range: 0.05-1 ppm CO) |
|
G3GA-1210 |
Determination of Carbonmonoxide in Air (Range: 0.1-10 % CO) |
|
G3GA-1211 |
Determination of Carbonmonoxide in Air (Range: 100-1000 ppm CO) |
|
G3GA-1212 |
Determination of Carbonmonoxide in Air (Range: 10-100 ppm CO) |
|
G3GA-1213 |
Determination of Carbonmonoxide in Air (Range: 1-10 ppm CO) |
|
G3GA-1214 |
Determination of Carbonmonoxide in Air (Range: 0.05-1 ppm CO) |
|
G3GA-1300 |
Determination of Methane in Nitrogen (Range: 0.1-1 % CH4 in N2) |
|
G3GA-1310 |
Determination of Methane in Air (Range: 0.05-5 % CH4) |
|
G3GA-1400 |
Determination of Propane in Nitrogen (Range: 0.1-1 % C3H8) |
|
G3GA-1401 |
Determination of Propane in Nitrogen (Range: 10-1000 ppm C3H8) |
|
G3GA-1402 |
Determination of Propane in Nitrogen (Range: 2-10 ppm C3H8) |
|
G3GA-1410 |
Determination of Propane in Air (Range: 0.1-5 % C3H8) |
|
G3GA-1411 |
Determination of Propane in Air (Range: 10-1000 ppm C3H8) |
|
G3GA-1412 |
Determination of Propane in Air (Range: 2-10 ppm C3H8) |
|
G3GA-1500 |
Determination of Oxygen in Nitrogen |
|
G3GA-1600 |
Determination of Nitrogenmonoxide in Nitrogen |
|
G3GA-1700 |
Determination of Sulfurdioxide in Nitrogen |
|
G3GA-1800 |
Determination of Nitrogendioxide in Nitrogen |
|
G3GA-1900 |
|
|
G3GA-4100 |
Automotive Exhaust Gas Analyses |
|
G3GA-5100 |
Natural Gas Analyses |
2 |
G3GA-5200 |
Biogas Analyses |
3 |
G3GA-5300 |
|
|
G3GA-9101 |
?13C-CO2 Isotope Ratio Measurements in Gases |
|
G3GA-9102 |
?18O-CO2 Isotope Ratio Measurements in Gases |
|
G3GA-9800 |
Determination of Calorific Values of Solid Materials |
|
G3GA-9801 |
Determination of Calorific Values of Liquid Materials |
|
G3GA-9802 |
Determination of Calorific Values of Gas Materials |
|
G3GA-9900 |
Special Calibration / Test |
1 |
(1) |
Price depends on the requirements. |
(2) |
Components and range (%): Hydrogen: 0.1-10.0 Helium: 0.05-0.5 Nitrogen: 0.1-19.9 Carbondioxide: 0.02-45.0 Ethane: 0.02-11.0 Propane: 0.005-4.0 i-butane: 0.03-0.7 n-butane: 0.03-0.7 neo-pentane: 0.01-0.05 i-pentane: 0.02-0.7 n-pentane: 0.02-0.7 n-hexane: 0.01-0.3 Methane (balance): 42.0-99.0 |
(3) |
Components and range (%): Nitrogen: 4 - 25 Carbondioxide: 10 - 45 Hydrogen: 0.2 - 5 Oxygen: 0.1 - 3 Ethane: 0.01 - 0.20 Propane: 0.001 - 0.20 Methane (balance): 30 - 80 |
() |
|
GAUGE BLOCKS AND INTERFERENTIAL LENGTH MEASUREMENTS CALIBRATION / TEST LIST
CODE |
NAME |
NOTE |
G2BM-1100 |
Short Gauge Blocks: Grade 00, K Rectangular or Square Shape (measurement by interferometry) |
1,2 |
G2BM-1300 |
Short Gauge Blocks: Grade K,0,1,2 Rectangular or Square Shape (measurement by comparison) |
1,2 |
G2BM-1600 |
Long Gauge Blocks: Rectangular or Square Shape (length between 125-1000 mm)(measurement by comparison or measurement by mechanical probing) |
1,2 |
G2BM-1800 |
Special Gauge Sets for Calibration of Mechanical Comparator |
1 |
G2BM-4000 |
Optical Flat (Prices differ acc.to dimensions) |
1,2,3 |
G2BM-4100 |
Optical Parallel |
1,2 |
G2BM-4200 |
Optical Flat (with 3-Flat Method by interferometry) |
1,2 |
G2BM-4300 |
Mirror / Platen / Optical Surface Flatness Measurements (Max. Diameter 150 mm) |
1,2 |
G2BM-4400 |
PZT- Nanosensor |
1 |
G2BM-9100 |
Angular Interferometer and Angle Reflector |
1, 3 |
G2BM-9200 |
Penta Prism (Optical Square) |
1 |
G2BM-9300 |
Corner Cube (Retro Reflector) |
1 |
G2BM-9900 |
Special Calibration / Test |
3 |
(1) |
Acredited Item. |
(2) |
Prices are given per piece |
(3) |
Price of optic flat diameter ; d < 100 mm is 550 TL+KDV, 100 mm < d < 150mm is 1210 TL+KDV and d > 150 mm is 2300 TL+KDV. |
GEOMETRICAL STANDARTS AND FORM MEASUREMENTS LABORATORY CALIBRATION / TEST LIST
CODE |
NAME |
NOTE |
G2BF-0100 |
Roundness Standards |
1, 3, 4 |
G2BF-0110 |
Magnification Standard (Flick) |
1 |
G2BF-0200 |
Reference Ring-Plug Gauge, Spherical Standard (for CMM) (for Set-up purposes), calibration with length measuring machine (price per piece) |
1 |
G2BF-0210 |
Spherical Standard for Optical Projectors (calibration with length measuring machine) |
1 |
G2BF-0300 |
Plain Go-NoGo Ring-Plug Gauge (calibration with length measuring machine) |
1 |
G2BF-0400 |
Parallel Thread Ring-Plug Gauge (calibration with length measuring machine) |
1 |
G2BF-0410 |
Thread Measuring Probes (double sided spherical probe) |
1,3 |
G2BF-0500 |
Thread Measuring Pins (3 pieces) |
1 |
G2BF-0510 |
Gear Measuring Pins (2 pieces) |
1 |
G2BF-0520 |
Pin Gauge (1 pieces) |
1 |
G2BF-1200 |
Electronic Displacement Transducers (1-D Displacement Transducers, actuators) |
1 |
G2BF-1210 |
Electronic Displacement Transducers (1-D Displacements Transducers, actuators) (calibration with Nano sensor, ± 7µm range) |
1 |
G2BF-1510 |
Dial-Indicator Tester (Resolution #?## 0.1micrometer) |
1, 3 |
G2BF-2000 |
Steel Tape (surveyor levelling rod, engineer tape, engineer scale, PI tape, geodetic wire) and Steel Rule (Up to 10m for 10 measurement points) |
1,2 |
G2BF-2020 |
Precision Line Scale (Glass Rule for Microscope and optical projectors) calibration with Optical Projector for 10 measurement points |
1,2 |
G2BF-2021 |
Precision Line Scale (Glass Rule for Microscope and optical projectors) calibration with optical projector equipped with laser Interferometer for10 measurement points |
1,2 |
G2BF-2030 |
Stage Micrometer (calibration with Mask Measuring Machine equipped with Differential Interferometer for10 measurement points.) |
1,2 |
G2BF-9900 |
Special Calibration / Test |
3 |
(1) |
Acredited Item. |
(2) |
When measurements with more than 10 points are requested, 35 TL for each measuring point must be added to the price. The price is for the measurements of one face and one side of one scale on the ruler. |
(3) |
Price quoted will be determined acc. to request. Prices differ depending on the service. Given price is the lowest calibration price |
(4) |
|
HARDNESS LABORATORY CALIBRATION / TEST LIST
CODE |
NAME |
NOTE |
G2ST-1100 |
Rockwell / Calibration of Hardness Reference Blocks |
1 |
G2ST-1300 |
Brinell / Calibration of Hardness Reference Blocks |
1 |
G2ST-1500 |
Vickers / Calibration of Hardness Reference Blocks |
1 |
G2ST-5300 |
Rockwell Conical Diamond Indenters for Rockwell A, C, D, N Scales |
1 |
G2ST-5500 |
Vickers Pyramid Diamond Indenters |
1 |
G2ST-9900 |
Special Calibration / Test |
2, 3 |
(1) |
The service is in the acrreditation scope. |
(2) |
In case of outside calibration, accommodation and traveling costs are under responsibility of customer. |
(3) |
Price will be determined according to the request and the standards. |
HIGH VOLTAGE LABORATORY CALIBRATION / TEST LIST
CODE |
NAME |
NOTE |
G1YG-1050 |
DC High Voltage Measuring System Calibration (100 kV - 400 kV) |
1, 2, 3, 7,11 |
G1YG-1250 |
DC High Voltage Measuring System/Probe Calibration (1 kV - 100 kV) |
1, 2, 3, 7, 11 |
G1YG-2050 |
AC High Voltage Measuring System Calibration (45 Hz-60 Hz, 101 kV - 400 kV) |
1, 2, 3, 9, 11 |
G1YG-2555 |
Calibration of High Frequency High Voltage Measuring System (50 Hz-300 Hz, 1 kV-200 kV) |
2, 3, 9, 11 |
G1YG-2655 |
Calibration of VLF (Very Low Frequency) AC High Voltage Device (1 kV-120 kV) |
2, 3, 9, 11 |
G1YG-2800 |
Calibration of AC High Voltage Measuring System (45 Hz-60 Hz, 1 kV - 100 kV) |
1, 2, 3, 9 |
G1YG-3050 |
Lightning Impulse High Voltage Measuring System Calibration (40kV - 1000kV) |
1, 2, 3, 11 |
G1YG-3100 |
Switching Impulse High Voltage Measuring System Calibration (40kV - 850kV) |
1, 2, 3, 11 |
G1YG-3200 |
Impulse High Voltage Measuring System/Probe Calibration (<40 kV) |
1, 2, 3, 11 |
G1YG-3250 |
Impulse High Voltage Source Calibration (1 kV - 40 kV) (Includes volatge and current option) |
1, 2, 3, 11 |
G1YG-3260 |
Calibration of Impulse High Current Shunt/Probe |
2, 3, 11 |
G1YG-4400 |
PD Detector Calibration (>2 pC) |
1, 2, 3, 11 |
G1YG-4450 |
PD Calibrator Calibration |
1, 2, 3, 11 |
G1YG-4451 |
Surge Device Calibration |
2, 3, 11 |
G1YG-4452 |
Electrostatic Field Meter Calibration |
2, 3, 11 |
G1YG-5060 |
Calibration of Capacitance and Dissipation Factor Measuring Device |
1, 2, 3, 4, 11 |
G1YG-5070 |
Calibration of Standard Capacitor |
1, 2, 3, 4, 11 |
G1YG-6000 |
Calibration of Oil Tester |
1, 2, 3, 11 |
G1YG-6025 |
Insulation Tester Calibration (up to 10 kV, Meger etc.) |
1, 2, 3, 7, 8, 11 |
G1YG-6050 |
Calibration of High Voltage Field Meter |
1, 2, 3, 11 |
G1YG-9900 |
Special High Voltage Test/Measurements |
2, 3, 5, 6, 10 |
(1) |
All our activities are peformed according to IEC 60060-2 standard. |
(2) |
The calibrations have been priced for five measuring points at least. For the each additional measuring point, 10% of extra charge will be added to the calibration fee. |
(3) |
Customer is responsible to supply the uninterrupted source for on-site calibration according to the IEC 60060-1 and IEC 60060-2. No any repay in the case of problem about breakdown, out of system etc. |
(4) |
C/tand measurement and calibrations performed in the TÜBİTAK UME High Voltage Laboratory under (50 Hz) AC high voltage and up to 400 kV. On site C/tand measurement and calibrations performed maximum up to 10kV.. |
(5) |
Opening hours are 08:00 to 12:00 and 13:00 to 16:30. |
(6) |
Pricing is based on demand. |
(7) |
Calibration cost for one polarty.For double polarty %50 calibration cost is added. |
(8) |
|
(9) |
Our accreditation scope can be reached from TÜRKAK web site (www.turkak.org.tr). |
(10) |
|
(11) |
|
HUMIDITY LABORATORY CALIBRATION / TEST LIST
CODE |
NAME |
NOTE |
G1NM-1000 |
Calibration of Dew-Point Hygrometer (-30 °C / +60 °C ; at 4 calibration points) |
1, 2, 3, 6 |
G1NM-1500 |
Calibration of Dew-Point Hygrometer (-40 °C / +10 °C ; at 3 calibration points) |
1, 2, 3, 6 |
G1NM-1600 |
Calibration of Dew-Point Hygrometer (-80 °C / +10 °C ; at 3 calibration points) |
1,2,3,6 |
G1NM-2000 |
Calibration of Hygrometer Relative Humidity (3 relative humidity calibration points at one temperature value) |
1, 2, 3, 6 |
G1NM-2100 |
Calibration of Hygrometer Relative Humidity (3 relative humidity calibration points at one temperature value in the climatic chamber) |
1, 2, 3, 6 |
G1NM-2500 |
Calibration of Hygrometer Temperature ( 3 temperature calibration points at one relative humidity value) |
1, 2, 3, 6 |
G1NM-2600 |
Calibration of Hygrometer Temperature ( 3 temperature calibration points at one relative humidity value in the climatic chamber) |
1, 2, 3, 6 |
G1NM-3000 |
Calibration of Relative Humidity Chamber (at 1 relative humidity calibration point) |
1, 2, 3, 6 |
G1NM-4000 |
Calibration of Psychrometer (at 3 calibration points) |
1, 2, 3, 6 |
G1NM-5000 |
Humidity Characterization of Climatic Chamber (one calibration point) |
1, 2, 6 |
G1NM-5100 |
Humidity Calibration of Climatic Chambers (at 3 calibration points) |
1, 2, 6 |
G1NM-5500 |
Air Temperature Characterization of Climatic Chamber (From -40 °C to 100 °C, one calibration point) |
1, 2, 6 |
G1NM-5600 |
Air Temperature Calibration of Climatic/Temperature Chambers (at 3 calibration points) |
1, 2, 6 |
G1NM-6000 |
Moisture content determination in materials (Paper and solid biomass)(at 3 calibration points) |
1,3,4,6,7 |
G1NM-9900 |
Special Calibration / Test |
2, 3, 4, 5, 6 |
(1) |
This item is in the scope of accreditation. |
(2) |
Please specify dew-point temperature, relative humidity, and air temperature values in your calibration request. The technical manual of the device to be calibrated, previous calibration certificates, and related documents should be sent together with the device. |
(3) |
Please send the device including all components i.e. connection and power cables, spare battery, software together with PC, etc. ready for measurements. Please specify clearly if your instrument works with power supply other than 220 VAC. |
(4) |
Please send the samples you use and/or standards you apply. |
(5) |
Price will be determined according to technical requirements. |
(6) |
Please note that laboratory will not be held responsible not only for any damages occurring to the equipment during the calibration process but also during the transportation. |
(7) |
Moisture content determination is carried out only for paper based and solid biomass materials. |
() |
|
() |
|
INORGANIC LABORATORY CALIBRATION / TEST LIST
CODE |
NAME |
NOTE |
G3IK-3001 |
Determination of As in Sea Fish |
1 |
G3IK-3002 |
Determination of Hg in Sea Fish |
1 |
G3IK-3003 |
Determination of As in Herb |
1 |
G3IK-3004 |
Determination of Ca in Herb |
1 |
G3IK-3005 |
Determination of Cd in Herb |
1 |
G3IK-3006 |
Determination of Pb in Herb |
1 |
G3IK-3007 |
Determination of Zn in Herb |
1 |
G3IK-3008 |
Determination of Pb in Wine |
1 |
G3IK-3009 |
Determination of Zn in Soybean |
1 |
G3IK-3010 |
Determination of Zn in Soybean |
1 |
G3IK-3011 |
Determination of AsB |
|
G3IK-3012 |
Determination of Cu in Ethanol |
|
G3IK-3013 |
Determination of Cu in Infant Formula |
1 |
G3IK-3014 |
Determination of I in Infant Formula |
1 |
G3IK-3015 |
Determination of K in Infant Formula |
1 |
G3IK-3020 |
Determination of elements in hazelnut |
1 |
G3IK-3101 |
Determination of Sr in Sea Water |
1 |
G3IK-3102 |
Determination of Na in Sea Water |
1 |
G3IK-3103 |
Determination of Mg in Sea Water |
1 |
G3IK-3104 |
Determination of Ca in Drinking Water |
1 |
G3IK-3105 |
Determination of Cd in Drinking Water |
1 |
G3IK-3106 |
Determination of Ni in Drinking Water |
1 |
G3IK-3107 |
Determination of Pb in Drinking Water |
1 |
G3IK-3108 |
Determination of Pb Isotopic Composition in Water |
|
G3IK-3109 |
Determination of As in Drinking Water |
1 |
G3IK-3110 |
Determination of B in Drinking Water |
1 |
G3IK-3111 |
Determination of Cr in Drinking Water |
1 |
G3IK-3112 |
Determination of Mo in Drinking Water |
1 |
G3IK-3113 |
Determination of Cr(VI) in Drinking Water |
|
G3IK-3114 |
Determination of Se in water |
1 |
G3IK-3120 |
Determination of elements in sea water |
1 |
G3IK-3130 |
Determination of elements in waste water |
1 |
G3IK-3201 |
Determination of (SO42-) in sea water |
|
G3IK-3204 |
Determination of Pb in Salt Solutions |
1 |
G3IK-3205 |
Determination of Pb Isotopic Composition in Salt Solutions |
|
G3IK-3301 |
Determination of As in biological materials |
1 |
G3IK-3302 |
Determination of Pb in Biological Materials |
1 |
G3IK-3303 |
Determination of Cr in Biological Materials |
1 |
G3IK-3304 |
Determination of Ni in Algae |
1 |
G3IK-3305 |
Determination of Ni in Algae |
1 |
G3IK-3306 |
Determination of K in Human Serum |
1 |
G3IK-3307 |
Determination of Ca in Human Serum |
1 |
G3IK-3308 |
Determination of Mg in human serum |
1 |
G3IK-3309 |
Determination of Fe in Human Serum |
1 |
G3IK-3310 |
Determination of Selenomethionine in Human Serum |
|
G3IK-3311 |
Determination of Cl in Serum |
1 |
G3IK-3312 |
Determination of Cu in Serum |
1 |
G3IK-3313 |
Determination of Na in Serum |
1 |
G3IK-3314 |
Determination of P in Serum |
1 |
G3IK-3315 |
Determination of Se in Serum |
1 |
G3IK-3316 |
Determination of As in Leather |
1 |
G3IK-3317 |
Determination of Cd in Leather |
1 |
G3IK-3318 |
Determination of Pb in Leather |
1 |
G3IK-3319 |
Determination of TBT in leather |
|
G3IK-3320 |
Determination of Hg in biological materials |
1 |
G3IK-3321 |
Determination of Ni in biological materials |
1 |
G3IK-3322 |
Determination of P in biological materials |
1 |
G3IK-3323 |
Determination of Zn in biological materials |
1 |
G3IK-3401 |
Determination of Ag in Metallic Zinc |
1 |
G3IK-3402 |
Determination of Al in Metallic Zinc |
1 |
G3IK-3403 |
Determination of Cd in Metallic Zinc |
1 |
G3IK-3404 |
Determination of Cr in Metallic Zinc |
1 |
G3IK-3405 |
Determination of Ni in Metallic Zinc |
1 |
G3IK-3406 |
Determination of Tl in Metallic Zinc |
1 |
G3IK-3407 |
Determination of Total Impurity in Metallic Zinc |
|
G3IK-3408 |
Determination of Pb Isotopic Composition in Bronze |
|
G3IK-3420 |
Detection and determination of impurities in metals and alloys |
|
G3IK-3421 |
Determination of O, N and H in metals and alloys |
|
G3IK-3422 |
Determination of C and S in metals and alloys |
|
G3IK-3501 |
Determination of Co in Single Element Calibration Solution |
|
G3IK-3601 |
Determination of As in cosmetic material |
1 |
G3IK-3602 |
Determination of Pb in Cosmetic Material |
1 |
G3IK-3603 |
Determination of Hg in Cosmetic Material |
1 |
G3IK-3701 |
Determination of Ca in Biodiesel Fuel |
1 |
G3IK-3702 |
Determination of K in Biodiesel Fuel |
1 |
G3IK-3703 |
Determination of Mg in Biodiesel Fuel |
1 |
G3IK-3704 |
Determination of Na in Biodiesel Fuel |
1 |
G3IK-3705 |
Determination of P in Biodiesel Fuel |
1 |
G3IK-3710 |
Determination of S in diesel |
|
G3IK-3801 |
Determination of As in Soil |
1 |
G3IK-3802 |
Determination of Cd in Soil |
1 |
G3IK-3803 |
Determination of Fe in Soil |
1 |
G3IK-3804 |
Determination of Mn in Soil |
1 |
G3IK-3805 |
Determination of Pb in Soil |
1 |
G3IK-3900 |
Determination of elements in bor minerals |
1 |
G3IK-9900 |
Special Calibration / Test |
2 |
(1) |
Price to be added for measurement of each additional parameter in the sample is 61 TL. |
(2) |
Price depends on the requirements. |
() |
|
MAGNETICS LABORATORY CALIBRATION / TEST LIST
CODE |
NAME |
NOTE |
G1MA-1110 |
Characterization of permanent magnets |
|
G1MA-3100 |
Reference magnets |
|
G1MA-4100 |
Field Coils |
|
G1MA-5110 |
Magnetometers (1 measurement range) |
|
G1MA-5120 |
Magnetometers (2 measurement ranges) |
|
G1MA-5130 |
Magnetometers (3 measurement ranges) |
|
G1MA-5140 |
Magnetometers (4 measurement ranges) |
|
G1MA-5150 |
Magnetometers (5 and more measurement ranges) |
|
G1MA-6100 |
Fluxmeters |
|
G1MA-7100 |
Magnetic stripes on identification cards |
|
G1MA-9900 |
Special Calibration / Test |
1 |
(1) |
Cost of the service is determined based on your request. |
MASS LABORATORY CALIBRATION / TEST LIST
CODE |
NAME |
NOTE |
G2KU-1110 |
E1 Class 1 mg- 1 kg |
1 |
G2KU-1150 |
E2 Class 1 mg - 1 kg |
1 |
G2KU-1210 |
E1 Class 2 kg - 10 kg |
1 |
G2KU-1250 |
E2 Class 2 kg - 10 kg |
1 |
G2KU-1310 |
E1 Class 20 kg - 50 kg |
1 |
G2KU-1350 |
E2 Class 20 kg - 50 kg |
1 |
G2KU-1450 |
E2 Class over 50 kg |
1 |
G2KU-5300 |
Determination of volume or density of solids in the range of 1 g – 1 kg |
|
G2KU-5400 |
Determination of volume or density of solids in the range of 2 kg– 10kg |
|
G2KU-5500 |
Determination of volume or density of solids in the range of 20kg– 50 kg |
|
G2KU-9900 |
Special Calibration / Test |
2 |
(1) |
In case of volume determination of the weight, % 50 of the calibration price will be added to the total price. |
() |
The price will be determined according to the request and the standards. |
ORGANIC CHEMISTRY LABORATORY CALIBRATION / TEST LIST
CODE |
NAME |
NOTE |
G3OK-10000 |
|
|
G3OK-10100 |
|
|
G3OK-10200 |
|
|
G3OK-10300 |
|
|
G3OK-10400 |
|
|
G3OK-10500 |
|
|
G3OK-10600 |
|
|
G3OK-2000 |
Determination of δ2H/1H, δ18O/16O ratio in water by IR-MS |
|
G3OK-2200 |
Determination of δ13C/12C ratio in sugar by IR-MS |
|
G3OK-2400 |
Analysis of δ13C/12C in honey and grape molasses by IRMS |
|
G3OK-2500 |
Determination of ?15C/14N ratio in Fish muscle by IR-MS |
|
G3OK-4000 |
Determination of Chloramphenicol in Meat |
|
G3OK-4001 |
Determination of Chloramphenicol in Milk |
|
G3OK-4002 |
Determination of Chloramphenicol in Honey |
|
G3OK-4101 |
Determination of Tetracycline Group Antibiotics in Meat |
|
G3OK-4102 |
Determination of Tetracycline Group Antibiotics in Milk |
|
G3OK-4201 |
Determination of Sulphonamide Group Antibiotics in Meat |
|
G3OK-4202 |
Determination of Sulphonamide Group Antibiotics in Milk |
|
G3OK-4300 |
Purity Assesment of Organic Compounds |
|
G3OK-4400 |
Purity Assesment of Chloramphenicol |
|
G3OK-4500 |
Determination of Chlorinated Pesticides in Tea |
|
G3OK-4600 |
Determination of 3-epi-25-Hydroxyvitamin D3 in Serum |
|
G3OK-4610 |
Determination of vitamine 25-OH D2 |
|
G3OK-4620 |
Determination of vitamine 25-OH D3 |
|
G3OK-4700 |
Determination of Coenzyme Q10 in food supplements |
|
G3OK-4801 |
Determination of Water-Soluble Vitamines in food supplements (B1, B2, B3, B5, B6, B9, B12, C) |
2 |
G3OK-4802 |
Determination of Fat Soluble Vitamines in food supplements (A, D3, E) |
2 |
G3OK-4900 |
Determination of Methyl Sulfonyl Methane (MSM) in food supplements |
|
G3OK-5000 |
Determination of EPA, DHA and total oil (fish oil) in fish oil |
|
G3OK-5200 |
Determination of Chondroitine in food supplements |
|
G3OK-5300 |
Determination of Glucosamine in food supplements |
|
G3OK-5400 |
Determination of beta 1,3-1,6 glucan in food supplements |
|
G3OK-5600 |
Determination of Cholesterol in Serum |
|
G3OK-5700 |
Determination of Glucose in Serum |
|
G3OK-5800 |
Determination of Creatinine in Serum |
|
G3OK-6000 |
Determination of Benzoic Acid, Methy Paraben, n-Butyl Paraben,Sorbic Acid and Propionic Acid in Soya Sauce, Water, Aqueous-Based Beverages and Aqueous-Based Condiments |
2 |
G3OK-6200 |
Determination of Sodium Benzoate and Potassium sorbate in Food and Beverages |
2 |
G3OK-6300 |
Determination of Sodium Benzoate and Potassium sorbate in Ketchup |
2 |
G3OK-6400 |
Determination of ?-cyanoalanine (BCA) and ?-glutamyl ?-cyanoalanine (?GBCA) in Lentil |
2 |
G3OK-6500 |
Determination of BDE-47 in Sediment |
|
G3OK-6600 |
Determination of PAH in Organic Solutions |
|
G3OK-6700 |
Determination of PAH in Plant Matrices |
|
G3OK-6800 |
Determination of AFB1, AFB2, AFG1, AFG2 and Total AF in Dried Fig |
|
G3OK-6900 |
Determination of Urea and Uric Acid in Biological Matrix |
|
G3OK-7000 |
The measurement of National Marker, return and disposal procedures |
1 |
G3OK-7100 |
Determination of Enrofloxacin and Sulfadiazine in Meat |
|
G3OK-7200 |
Determination of Amino asid in Aqueous Solution |
|
G3OK-7300 |
Determination of Ethanol in Water |
|
G3OK-7400 |
Determination of Specific Adsorption of Nonporous Silicon Dioxide (Sio2) and BET Specific Surface Area |
|
G3OK-7500 |
Determination of PAH in Vegetable oils |
|
G3OK-7600 |
Determination of Phthalate Esters in Polyvinyl Chloride |
|
G3OK-7700 |
Determination of Zearolenone in Acetonitrile |
|
G3OK-7800 |
|
|
G3OK-7900 |
|
|
G3OK-8000 |
Determination of d13C/12C ratio in Vanillin by IR-MS |
|
G3OK-8400 |
|
|
G3OK-8500 |
|
|
G3OK-8600 |
|
|
G3OK-8700 |
|
|
G3OK-8800 |
|
|
G3OK-8900 |
|
|
G3OK-9000 |
|
|
G3OK-9100 |
|
|
G3OK-9200 |
|
|
G3OK-9300 |
|
|
G3OK-9400 |
|
|
G3OK-9500 |
|
|
G3OK-9600 |
|
|
G3OK-9700 |
|
|
G3OK-9800 |
|
|
G3OK-9900 |
Special Calibration / Test |
1 |
(1) |
Price depends on the requirements. |
(2) |
Price is given per analyte. |
PHOTOVOLTAIC PERFORMANCE TESTS LABORATORY CALIBRATION / TEST LIST
CODE |
NAME |
NOTE |
G1FV-0100 |
Visual Inspection Experiment |
1, 2, 3, 4, 10, 12 |
G1FV-0200 |
Maximum Power Experiment |
2, 3, 4, 5, 6 |
G1FV-0250 |
|
2, 3, 4, 5, 6 |
G1FV-0300 |
Insulation Resistance Experiment |
3, 4 |
G1FV-0400 |
Temperature Coefficient Experiment |
3, 4, 6, 7, 12 |
G1FV-0500 |
Nominal Module Operating Temperature (NMOT) Experiment |
3, 4 |
G1FV-0600 |
Performance Test of Module at STC and NMOT Conditions |
3, 4, 5, 6, 12 |
G1FV-0700 |
Low Irradiance Performance Experimet |
3, 4, 5, 6, 12 |
G1FV-0800 |
Outdoor Exposure Experiment |
3, 4 |
G1FV-0900 |
Hot-Spot Endurance Experiment |
1, 2, 3, 4, 5, 6 |
G1FV-1000 |
UV Preconditioning Experiment (15 kWh) |
1, 2, 3, 4, 5, 6, 12 |
G1FV-1100 |
Thermal Cycling Experiment |
1, 2, 3, 4, 5, 6 |
G1FV-1200 |
Humidity Freeze Experiment |
1, 2, 3, 4, 5, 6 |
G1FV-1300 |
Damp Heat Experiment |
1, 2, 3, 4, 5, 6 |
G1FV-1400 |
Robustness of Terminations Experiments |
1, 2, 3, 4, 5, 6 |
G1FV-1500 |
Wet Leakage Current Experiment |
1, 2, 3, 4, 5, 6 |
G1FV-1600 |
Mechanical Load Experiment |
1, 2, 3, 4, 5, 6, 12 |
G1FV-1650 |
|
1, 2, 3, 4, 5, 6, 12 |
G1FV-1700 |
Hail Experiment |
1, 2, 3, 4, 5, 6, 12 |
G1FV-1800 |
Bypass Diode Thermal |
1, 2, 3, 4, 5, 6 |
G1FV-1850 |
Bypass Diode Functionality Experiment |
1, 2, 3, 4, 5, 6, 12 |
G1FV-1900 |
Stabilisation Experiment |
1, 2, 3, 4, 5, 6, 12 |
G1FV-2000 |
Accessibility Experiment |
1, 2, 3, 4, 5, 6 |
G1FV-2100 |
Cut Susceptibility Experiment |
1, 2, 4 |
G1FV-2200 |
Ground Continuity Experiment |
1, 2, 4 |
G1FV-2300 |
Impulse Voltage Experiment |
1, ,2, 4 |
G1FV-2400 |
Tempereture Experiment |
11 |
G1FV-2500 |
Fire Experiment |
11 |
G1FV-2600 |
Reverse Current Overload Experiment |
1, ,2, 4 |
G1FV-2700 |
Module Breakage Deneyi |
1, ,2, 4 |
G1FV-2800 |
Materials Creep Experiment |
11 |
G1FV-2900 |
UV Experiment |
1, ,2, 4 |
G1FV-3000 |
Cold Conditioning Experiment |
11 |
G1FV-3100 |
Dry Heat Conditioning Experiment |
11 |
G1FV-3200 |
Spectral Responsivity Experiment |
1, 2, 3, 5, 6, 12 |
G1FV-3300 |
Light Induced Degradation (LID) Experiment |
11 |
G1FV-3400 |
Potantial Induced Degradation (PID) Experiment |
8, 11 |
G1FV-3500 |
Energy Rating Experiment |
9, 11 |
G1FV-3600 |
Reference Cell Calibration |
2, 3, 5 |
G1FV-3700 |
Simulator Classifications
|
5, 7 |
G1FV-9900 |
Special Calibration / Test |
11 |
(1) |
The experiment is performed according to IEC 61215-2 standard. |
(2) |
The experiment is performed according to IEC 61730-2 standard. |
(3) |
The experiment is performed according to IEC 61730-2 standard. |
(4) |
The experiment is performed according to IEC 61853-1 standard. |
(5) |
The experiment is performed according to IEC TS 61853-2, Method A standard. |
(6) |
The price will be evaluated with respect to the experiments sequence given in the standard |
(7) |
The experiment is performed according to IEC TS 62804-1, Method A standard. |
(8) |
|
(9) |
|
(10) |
|
(11) |
|
(12) |
|
POWER AND ENERGY LABORATORY CALIBRATION / TEST LIST
CODE |
NAME |
NOTE |
G1PE-1200 |
Wattmeter/Energymeter Calibration (by AC Power Measurement Standard) |
1 |
G1PE-1210 |
Wattmeter/Energymeter Calibration (by Three Phase Standard Wattmeter/Energymeter) |
1 |
G1PE-1300 |
Power/Energy Analyzer Calibration (by Three Phase Standard Wattmeter/Energymeter) |
1 |
G1PE-1310 |
Power/Energy Analyzer Calibration (by Electrical Power Standard) |
1 |
G1PE-1510 |
Electricity Meter Calibration (Single or Three Phase), Active |
1 |
G1PE-1520 |
Electricity Meter Calibration (Single or Three Phase), Reactive |
1 |
G1PE-1700 |
Phase Meter Calibration |
|
G1PE-1800 |
Phase Standard Calibration |
|
G1PE-1920 |
AC Power Source Calibration, Three Phase |
1 |
G1PE-2000 |
Electrical Power Standard Calibration |
1 |
G1PE-5000 |
Current Transformer Calibration (Ratio and Phase Error) |
1 |
G1PE-5010 |
Multiratio Current Transformer Calibration |
1, 2 |
G1PE-5100 |
Current Transformer Test Set Calibration |
1 |
G1PE-5200 |
Standard Current Burden Calibration |
1 |
G1PE-6000 |
Voltage Transformer Calibration (Ratio and Phase Error) |
1 |
G1PE-6010 |
Multiratio Voltage Transformer Calibration |
1, 2 |
G1PE-6100 |
Voltage Transformer Test Set Calibration |
1 |
G1PE-6200 |
Standard Voltage Burden Calibration |
1 |
G1PE-9810 |
Transformer Loss Measurement System Calibration (On-site) |
1, 2 |
G1PE-9900 |
Special Calibration / Test |
2 |
(1) |
The service is in the acrreditation scope. |
(2) |
Price depends on the requirements. |
PRESSURE LABORATORY CALIBRATION / TEST LIST
CODE |
NAME |
NOTE |
G2BA-1100 |
Determination of Effective Area of Piston-Cylinder Unit |
1,2,3,6 |
G2BA-2100 |
Analogue Manometer Calibration |
1,2,4,6 |
G2BA-2110 |
Absolute Analogue Manometer Calibration |
1,2,6 |
G2BA-2200 |
Digital Manometer Calibration |
1,2,4,6 |
G2BA-2210 |
Absolute Digital Manometer Calibration |
1,2,6 |
G2BA-2500 |
Pressure Transducer Calibration |
1,2,4,6 |
G2BA-2510 |
Absolute Pressure Transducer Calibration |
1,2,6 |
G2BA-3100 |
Manometer Calibrator Calibration (Per Measuremet Range) |
1,2,4,6 |
G2BA-3110 |
Absolute Manometer Calibrator Calibration (Per Measuremet Range) |
1,2,4,6 |
G2BA-4100 |
Analogue Barometer Calibration |
1,2,6 |
G2BA-4200 |
Digital Barometer Calibration (from 800 hPa to 1200 hPa absolute ) |
1,2,6 |
G2BA-6100 |
Air Data Test Set Calibration (Per Measurement Range) |
1,2,6 |
G2BA-9900 |
Special Calibration / Test |
2,5,6 |
(1) |
Accredited Item |
(2) |
'20 percent of calibration fee is demanded in case of the instrument is not clean enough for the calibration.for DWT and vacuum gages. For the defective instrument determined by the tests (at about 20 hours later), 50 percent of calibration fee is demanded for vacuum gages. |
(3) |
Conventional mass values and its uncertainties will be given in the certificate of mass set of pressure balance |
(4) |
Only the calibration request for the pneumatic pressure ranges from 0 bar to (-1) bar and the range above 20 bars and for the hydraulic pressure range above the 700 bars will be responded. |
(5) |
Price is determined according to the specification of the demanded measurement. |
(6) |
Calibration fees announced are per measurement range or per sensor or per piston-cylinder unit |
() |
|
() |
|
QUANTUM METROLOGY LABORATORY CALIBRATION / TEST LIST
CODE |
NAME |
NOTE |
G1KM-9900 |
Custom Measurements and Experiments |
1-22 arası tüm notlar |
(1) |
|
(2) |
|
(3) |
|
(4) |
|
(5) |
|
(6) |
|
(7) |
|
(8) |
|
(9) |
|
(10) |
|
(11) |
|
(12) |
|
(13) |
|
(14) |
|
(15) |
|
(16) |
|
(17) |
|
(18) |
|
(19) |
|
(20) |
|
(21) |
|
(22) |
|
RADIATION THERMOMETRY LABORATORY CALIBRATION / TEST LIST
CODE |
NAME |
NOTE |
G1RS-1000 |
Calibration at Fixed-Point Blackbody |
1, 2, 3 |
G1RS-2000 |
Radiation Thermometer Calibration (-50 °C / 800 °C) |
1, 2, 3, 4, 6 |
G1RS-2100 |
Radiation Thermometer Calibration (800 °C / 1600 °C) |
1, 2, 3, 4, 6 |
G1RS-2200 |
Radiation Thermometer Calibration (1600 °C / 2600 °C) |
1, 2, 3, 4, 6 |
G1RS-2300 |
Radiation Thermometer Calibration (2600 °C / 3200 °C) |
1, 2, 3, 4, 6 |
G1RS-3000 |
Blackbody/IR Calibrator Calibration (-50 °C / +1600 °C) |
1, 2, 3, 4, 6 |
G1RS-4000 |
Infrared Forehead Thermometer Calibration (34 °C / 42 °C) |
2, 4, 7, 8 |
G1RS-9900 |
Special Calibration / Test |
2, 3, 4, 5, 6, 7 |
(1) |
Acredited Calibration. |
(2) |
Please note that laboratory will not be held responsible for any damages occurring to the equipment during the calibration and transportation process |
(3) |
Please specify the calibration temperature range in the calibration request form and send all relevant documents (manuals, past certificates etc) and accessories of the instrument |
(4) |
The price is given for a measurement at single temperature. |
(5) |
Price will be determined according to technical requirements demanded by the customer. |
(6) |
For the devices requiring electronic circuit connections;1- The customer shall send their employee to UME to make the connections 2- The customer must assume all responsibility for any adverse circumstances/incidents that may occur due to the connections during the measurements. |
(7) |
For IR calibrators and Black bodies, only emissivity measurements or only surface temperature measurements are not performed. They are performed together with the calibration application. |
(8) |
The emissivity measurements can only be performed for temperatures higher than 150 ° C. |
RADIOMETRY LABORATORY CALIBRATION / TEST LIST
CODE |
NAME |
NOTE |
G1RA-4100 |
UVA Irradiance Meter |
1 |
G1RA-4120 |
Total UVB Irradiance Responsivity (280 nm - 315 nm) |
2 |
G1RA-4130 |
Total UVC Irradiance Meter (200 nm - 280 nm) |
|
G1RA-4150 |
Spectral Irradiance Responsivity ( 280 nm-1100 nm) |
|
G1RA-4200 |
Spectral Irradiance of Sources, (W/m2 ), (250 nm-2500 nm) |
|
G1RA-4300 |
Solar Irradiance Meter (200nm-1100nm) |
|
G1RA-4400 |
Pyranometer |
3 |
G1RA-4600 |
Pyrheliometer |
3 |
G1RA-4700 |
Spectral Radiance Responsivity |
|
G1RA-4800 |
Spectral Radiance |
|
G1RA-6400 |
Pulsed Laser Energy (1064 nm, <= 150 mJ) |
4 |
G1RA-6500 |
Laser Power Meter |
5 |
G1RA-6700 |
Spectral Responsivity (380 nm-1100 nm) |
|
G1RA-6800 |
Spectral Responsivity (1100 nm-1650 nm) |
|
G1RA-6900 |
Spectral Responsivity (250 nm-380 nm) |
|
G1RA-9900 |
Special Calibration / Test |
5 |
(1) |
Calibration of a UVA detector is carried out under Spectroline SB-100P/F model irradiance lamp supported with a UV filter (Spectronics Corporation, model 2F958). Typical calibration points are 100 uW/cm^2, 500 uW/cm^2, 1000 uW/cm^2, 2000 uW/cm^2 and 3000 uW/cm^2. |
(2) |
Calibration of a UVB radiometer is carried out under a deuterium light sources. |
(3) |
Measurements are carried out at provided environmental conditions (June - September) |
(4) |
The calibration is performed at 355 nm, 532 nm and 1064 nm pulse wavelengths and at an energy range of 10 mJ to 200 mJ. The calibration fee is valid for only one wavelength. |
(5) |
The calibration is performed at 488 nm, 515 nm, 532 nm, 633 nm and 1064 nm laser (CW) wavelengths and at optical power range of 10 mW to 1000 mW. The price is valid only for measurements of two wavelengths. |
(6) |
The price will be determined according to technical requirements. |
REFERENCE MATERIALS LABORATORY CALIBRATION / TEST LIST
CODE |
NAME |
NOTE |
G3RM-1101 |
"Particle Size Distribution Analysis with Laser Diffraction Method (0.02 µm-2000 µm)-
Analysis of Powder in Dispersant or Direct Analysis of the Powder by Dry Suction Unit " |
|
G3RM-1102 |
Particle Size Distribution Analysis with Vibrating Dry Sieving (Up to 8 Sieves) (45 µm-2000 µm) |
|
G3RM-1103 |
Particle Size Distribution Analysis with Air Jet Dry Sieving (Up to 8 Sieves) (45 µm-2000 µm) |
|
G3RM-1104 |
Homogenisation (solid powder materials, one batch maximum 250 kg/250 Liters) |
1 |
G3RM-1105 |
Liyophilisation (one batch maximum 3.9 m2 shelf surface area and 40 kg ice condensing capacity) |
1 |
G3RM-1106 |
Determination of Aflatoksin B1, B2, G1, G2 and Total in Dried Fig by HPLC -FLD (with immunoaffinity purification and cobra cell derivatization) |
|
G3RM-9900 |
Special Calibration / Test |
1 |
(1) |
Price depends on the requirements. |
RF & MICROWAVE LABORATORY CALIBRATION / TEST LIST
CODE |
NAME |
NOTE |
G1MD-1000 |
Primary level power sensor calibration (up to 26.5 GHz) |
1, 2 |
G1MD-1100 |
Calibration Factor of RF power sensor or thermistor mount (up to 15 frequency) |
1, 2 |
G1MD-1300 |
RF power meter calibration |
3 |
G1MD-1500 |
RF power measurement |
1, 4 |
G1MD-2100 |
Transmission Coefficient (up to 60 dB, 45 MHz-26,5 GHz)
(up to 20 frequencies) |
1, 5, 6 |
G1MD-3000 |
Primary Level Calculable Impedance Standard (airline) Calibration (up to 50 GHz) |
7 |
G1MD-3100 |
Reflection coefficient, VSWR, return loss measurement (45 MHz-26,5 GHz) (up to 20 frequencies) |
1, 6 |
G1MD-3300 |
Network analyzer calibration |
8, 9 |
G1MD-4100 |
G1MD-4100 Directional Coupler Calibration (<=2 GHz) |
6, 10 |
G1MD-4200 |
Coaxial Calibration Kit Calibration |
6, 11 |
G1MD-4300 |
Waveguide Calibration Kit Calibration |
6, 11 |
G1MD-4400 |
Measurement of Dielectric Properties of Materials (up to 50 GHz) |
12, 13, 14 |
G1MD-4500 |
|
6, 10 |
G1MD-5100 |
Noise Source Calibration (up to 50 GHz) |
10, 14 |
G1MD-8100 |
Mobile Phone SAR Test (900 MHz, 1800 MHz) |
11, 15 |
G1MD-9900 |
Special Calibration / Test |
12, 16 |
(1) |
Accredited item. |
(2) |
If more frequency points are requested, 180 TL is added for each extra frequency point to the price. |
(3) |
Price depends on the requirements. |
(4) |
It is valid for three different traffic channel for one SIM card and one frequency (900 MHz or 1800 MHz) point. |
(5) |
|
(6) |
|
(7) |
|
(8) |
|
(9) |
|
(10) |
|
(11) |
|
(12) |
|
(13) |
|
(14) |
|
(15) |
|
(16) |
|
SPECTRO PHOTOMETRY LABORATORY CALIBRATION / TEST LIST
CODE |
NAME |
NOTE |
G1SP-1100 |
Luminous Flux (Tungsten Lamps, 2856 K), (5 lm-5000 lm) |
|
G1SP-1150 |
Spectral Luminous Flux ( LED and SSL Lamps with max. 10 cm size), (0,7 lm-30000 lm) |
|
G1SP-1500 |
Luminous Intensity (1 cd-10000 cd) |
1 |
G1SP-1550 |
Spatial Luminous Intensity ( Tungsten, LED and SSL Lamps with 2 cm size) |
8 |
G1SP-2100 |
Color Coordinates of Light Sources, (CIE-xy, CIE-u'v') |
|
G1SP-2300 |
Color Temperature of Light Sources (2856 K) |
2 |
G1SP-2500 |
Color Plate (CIEXYZ, CIExy, CIELAB, DeLtaE), 0°:45° |
3 |
G1SP-2700 |
Color Plate (CIEXYZ, CIExy, CIELAB, DeltaE), d:0° and d:8° |
3 |
G1SP-2900 |
Colorimeter (DeltaE), 0°:45° and d:8° |
3 |
G1SP-3100 |
Luminance Responsivity (Luminance Meter), (1 cd/m2-1000 cd/m2) |
4 |
G1SP-3300 |
Luminance Source (27 cd/m2-5000 cd/m2) |
|
G1SP-3500 |
Illuminance (Luxmeter), (0,1 lx - 5000 lx) |
5 |
G1SP-3600 |
Luminous Responsivity (Photometer Head), (0,0002 nA/lx - 10 mA/lx) |
|
G1SP-5000 |
Spectral Regular Reflectance |
6 |
G1SP-5300 |
Gloss (Gloss/ Gloss Plate) |
7 |
G1SP-5500 |
Spectral Diffuse Reflectance |
6 |
G1SP-6000 |
Absolute Diffuse Reflectance (250 nm-2500 nm) |
8 |
G1SP-7000 |
Spectrophotometer (UV/VIS) |
|
G1SP-7100 |
Spectral Regular Transmittance |
6 |
G1SP-7300 |
Total Transmittance |
6 |
G1SP-7400 |
Wavelength Measurements of Light Sources |
|
G1SP-7500 |
Diffuse Transmittance Meter (Densitometer) |
6 |
G1SP-7600 |
Diffuse Transmittance (Step Density Strip / Film) |
6 |
G1SP-9900 |
Special Calibration / Test |
8 |
(1) |
The price given is valid for single solid angle and single ray direction. |
(2) |
Calibration is performed only at 2856 K color temperature. |
(3) |
Only valid for one type of lightning condition |
(3) |
Only valid for one type of lightning condition |
(4) |
The illuminance measurements are carried out at 50 lx, 500 lx , 800 lx and 2000 lx levels. If the customer request measurements at different points, it must be stated during the application. The extra measurement points between 0,1 lx and 4000 lx are subjected to a separate pricing per each additional measurement point. |
(5) |
The price is valid for one of the two wavelength ranges listed below and applies to a single bandwidth (SBW).
1) 250 nm - 1100 nm
2) 1100 nm - 2500 nm
Two separate demands are required for neutral density filters and wavelength accuracy filters located in the same box.
|
(6) |
The price is valid for the angles of 20°, 60°, and 85° |
(7) |
The price will be determined according to the measurement conditions and customer request. |
(8) |
|
(9) |
|
SURFACE TEXTURE AND NANOMETROLOGY LABORATORY CALIBRATION / TEST LIST
CODE |
NAME |
NOTE |
G2BY-0100 |
Roughness Standard |
1,2 |
G2BY-0110 |
Depth Setting Standard |
1 |
G2BY-9900 |
Special Calibration / Test |
3 |
(1) |
Acredited Item. |
(2) |
Measurements are performed for one Cut-Off value. If more than one Cut-Off measurements are requested, 260 TLs for each Cut-Off value must be added to the price. |
(3) |
Price quoted will be determined acc. to request. Prices differ depending on the service. |
TIME / FREQUENCY AND WAVELENGTH LABORATORY CALIBRATION / TEST LIST
CODE |
NAME |
NOTE |
G1ZF-1100 |
Atomic Time and Frequency Standard |
|
G1ZF-1300 |
Stability Measurement of Laser Frequency |
|
G1ZF-1310 |
Interferometric Long Gauge Block Measurement |
2 |
G1ZF-1500 |
Quartz Time and Frequency Standard |
|
G1ZF-2100 |
Timer - Counter |
|
G1ZF-2500 |
Synthesized Sweeper / Signal Generator |
|
G1ZF-3100 |
Spectrum Analyzer |
|
G1ZF-3300 |
EMC Test Equipment (Burst / Discontinuous Interference Analyzer) |
|
G1ZF-3400 |
Audio Analyzer |
|
G1ZF-3800 |
Measurement Receiver |
|
G1ZF-9900 |
Special Calibration / Test |
1 |
(1) |
Pricing is determined with respect to the tests to be performed. |
(2) |
Per piece |
TOPOGRAPHIC AND INDUSTRIAL MEASUREMENTS CALIBRATION / TEST LIST
CODE |
NAME |
NOTE |
G2BT-0100 |
Theodolite |
1 |
G2BT-0200 |
Optical Level |
1,2 |
G2BT-9900 |
Special Calibration / Test |
3 |
(1) |
Acredited Item. |
(2) |
If optical level has optical micrometer, price of each micrometer is 200 TL. |
(3) |
Price quoted will be determined acc. to request. Prices differ depending on the service. |
TORQUE LABORATORY CALIBRATION / TEST LIST
CODE |
NAME |
NOTE |
G2TK-1100 |
Calibration of Torque Transducers |
1,2 |
G2TK-2200 |
Static Calibration of Indicating Torque Wrenches |
1, 4 |
G2TK-3100 |
Calibration of Hand Torque Tools |
1, 5 |
G2TK-4100 |
Calibration of Torque Wrench Calibration Devices (for each measuring range) |
1, 6, 8 |
G2TK-9900 |
Special Calibration / Test |
9 |
(1) |
The service is in the acrreditation scope. |
(2) |
|
(3) |
|
(4) |
|
(5) |
|
(6) |
|
(7) |
|
(8) |
|
(9) |
|
VACUUM LABORATORY CALIBRATION / TEST LIST
CODE |
NAME |
NOTE |
G2VK-1100 |
Pirani, Thermal Conductivity, Thermocouple Type Vacuum Gauges |
1, 2, 3 |
G2VK-1200 |
Capacitance Diaphragm Type Vacuum Gauges (CDG) |
1, 2 |
G2VK-2100 |
Cold and Hot Cathode Type Vacuum Gauges |
1, 2, 3 |
G2VK-2200 |
Spinning Rotor Type Vacuum Gauges |
1, 2, 3 |
G2VK-3100 |
Full Range Vacuum Gauges |
1, 2, 3 |
G2VK-5100 |
Hellium Leak rate detection in vacuum (1,1 E-5 mbarl/s - 2E-8 mbarl/s) |
4, 5 |
G2VK-9900 |
Special Calibration / Test |
6 |
(1) |
Acredited Item. |
(2) |
20 percent of calibration fee is demanded in case of the vacuum gauge is not clean enough for the calibration.If the vacuum gauge is found to be defective through tests (at least 16 hours) , 50 percent of calibration fee is demanded. |
(3) |
|
(4) |
|
(5) |
|
(6) |
|
VIBRATION LABORATORY CALIBRATION / TEST LIST
CODE |
NAME |
NOTE |
G2TI-1100 |
Absolute Calibration of Standard Reference Accelerometers by Laser Interferometry ( (Calibration at 1/3 octave band center frequencies in the frequency range 10 Hz to 10 kHz) |
1 |
G2TI-1500 |
Comparison Calibration of Accelerometers (at 160 Hz) and Determination of Frequency Response |
2,6 |
G2TI-1800 |
Absolute Calibration of Shock Transducers by Laser Interferometry |
1 |
G2TI-1900 |
Comparison Calibration of Shock Transducers |
7 |
G2TI-2100 |
Calibration of Vibration Exciter
(Calibration at each frequency other than 159.15 Hz is performed at additional cost of 440 TL). |
|
G2TI-2200 |
Calibration of Vibration Measuring Set
Calibration performed at the frequency of 160 Hz. Calibration at each frequency other than 160 Hz is performed at additional cost of 550 TL |
2 |
G2TI-3100 |
Calibration of Impact Hammer |
|
G2TI-4100 |
Measurement of Mechanical Vibrations (Total Amplitude) (up to 10 measurement points) |
3,4 |
G2TI-4200 |
Frequency Analysis of Mechanical Vibrations (up to 10 measurement points) |
3,4 |
G2TI-5100 |
Measurement of Gravity Acceleration |
5, 7 |
G2TI-6100 |
Calibration of Conditioning Amplifier |
8 |
G2TI-7100 |
Calibration of Impedance Head (Calibration at 1/3 octave band center frequencies in the frequency range 100 Hz to 8 kHz) |
|
G2TI-9900 |
Special Calibration / Test |
3,4,5 |
(1) |
Calibration at each frequency other than 160 Hz is performed at additional cost of 125 TL |
(2) |
Calibration cost for triaxial accelerometers and vibration meters with triaxial accelerometer is two times of the single axis calibration price. |
(3) |
Acredited Service for hand-arm vibration measurement. |
(4) |
Cost of the service is determined based on your request. |
(5) |
Accomodation and trasportation costs are added to the measurement cost |
(6) |
|
(7) |
|
(8) |
|
VISKOSITY LABORATORY CALIBRATION / TEST LIST
CODE |
NAME |
NOTE |
G2VI-1100 |
Determination of Kinematic Viscosity of Newtonian liquids in the range of 0,5 - 100 000 mm²/s |
1 |
G2VI-1200 |
Determination of Dynamic Viscosity of Newtonian liquids in the range of 0,5 - 100 000 mPa·s |
1 |
G2VI-1300 |
Determination of Viscometer constants of Ubbelohde viscometer in the range of 0 - 5 (K=0,001 - 100 mm²/s²) |
2 |
G2VI-1500 |
Calibration of Rotational Viscometer |
3 |
G2VI-9900 |
Special Calibration / Test |
4 |
(1) |
Measurements are carried out at 20°C, in case of any different temperature 1/4 of the calibration price will be added to the total price. |
(2) |
Determination of Viscometer constants of Ubbelohde viscometer in the range of 0 -– 2, 1/3 of the calibration price will be added to the total price. |
(3) |
In case of one more spindle use for calibration of rotational viscometer, 1/4 of the calibration price will be added to the total price for every spindle. |
(4) |
The price will be determined according to the request and the standards. |
VOLTAGE LABORATORY CALIBRATION / TEST LIST
CODE |
NAME |
NOTE |
G1LV-0100 |
DC Voltage Standard Calibration (1 V, 1.018 V, 10 V)
Single Voltage Value (by Josephson Array Voltage Standard) |
1 |
G1LV-0101 |
DC Voltage Standard Calibration (1 V, 1.018 V, 10 V)
Two Voltage Values (by Josephson Array Voltage Standard) |
1 |
G1LV-0102 |
DC Voltage Standard Calibration (1 V, 1.018 V, 10 V) Three Voltage Values (by Josephson Array Voltage Standard) |
1 |
G1LV-0110 |
DC Voltage Standard Calibration (1 V, 1.018 V, 10 V) Single Voltage Value (by DC Voltage Standard Group) |
1 |
G1LV-0111 |
DC Voltage Standard Calibration (1 V, 1.018 V, 10 V) Two Voltage Value (by DC Voltage Standard Group) |
1 |
G1LV-0112 |
DC Voltage Standard Calibration (1 V, 1.018 V, 10 V) Three Voltage Value (by DC Voltage Standard Group) |
1 |
G1LV-0120 |
Multifunction Transfer Standard |
1 |
G1LV-0200 |
Multifunction Calibrator Calibration (by Reference Standards) |
1 |
G1LV-0201 |
Multifunction Calibrator with External Amplifier Option (by Reference Standards) |
1 |
G1LV-0202 |
Multifunction Calibrator Calibration (by Reference Standards) (included adjustment procedure) |
1 |
G1LV-0203 |
Multifunction Calibrator with External Amplifier Option (by Reference Standards)(included adjustment procedure) |
|
G1LV-0204 |
Wideband Option Calibrator Calibration (by Reference Standards) |
1, 6 |
G1LV-0205 |
Multifunction Calibrator with Wideband and External Amplifier (by Reference Standards) |
1, 6 |
G1LV-0206 |
Wideband Option Calibrator Calibration (by Reference Standards)(included adjustment procedure) |
1, 6 |
G1LV-0207 |
Multifunction Calibrator with Wideband and External Amplifier Options (by Reference Standards)
(included adjustment procedure) |
1, 6 |
G1LV-0209 |
|
1 |
G1LV-0210 |
Multifunction Calibrator Calibration (by Working Standards) (DCV, ACV, DCI, ACI, R, C, T/C, P) |
1 |
G1LV-0211 |
Oscilloscope Option Calibrator Calibration (by Working Standards) |
1, 6 |
G1LV-0212 |
Multifunction Calibrator Calibration (by Working Standards) (DCV, ACV,DCI,ACI,R,C,T/C,P) (included adjustment procedure) |
1, 6 |
G1LV-0213 |
Oscilloscope Option Calibrator Calibration (by Working Standards)(included adjustment procedure) |
1, 6 |
G1LV-0214 |
Multifunction calibrator with Oscilloscope option (BW > 600 MHz) |
1, 6 |
G1LV-0215 |
Multifunction calibrator with Oscilloscope option (BW ? 300 MHz) (Adjustment included) |
1, 6 |
G1LV-0216 |
Multifunction calibrator with Oscilloscope option(300 MHz < BW ? 600 MHz) (Adjustment included) |
1, 6 |
G1LV-0217 |
Multifunction calibrator with Oscilloscope option (BW > 600 MHz) (Adjustment included) |
1, 6 |
G1LV-0220 |
DC Calibrator Calibration |
1 |
G1LV-0230 |
AC Calibrator Calibration |
1 |
G1LV-0240 |
Nanovoltmeter Calibration |
1 |
G1LV-0275 |
Multimeter Calibration (7 ½ digit) |
1 |
G1LV-0280 |
Multimeter Calibration (8 ½ digit by reference calibrator) |
1 |
G1LV-0281 |
Multimeter Calibration (8 ½ digit by reference calibrator) (included adjustment procedure) |
1 |
G1LV-0285 |
Multimeter Calibration (8 ½ digit by reference standards) |
1 |
G1LV-0286 |
Multimeter Calibration (8 ½ digit) (by reference standards)
(included adjustment procedure) |
1 |
G1LV-0300 |
AC/DC Current Shunt Calibration (100 µA - 100 A, 10 Hz - 100 kHz) |
1, 3 |
G1LV-0301 |
Shunt Calibration (AC and DC) (Fluke Y5020) |
|
G1LV-0400 |
AC/DC Transfer Standard Calibration (10 Hz-1 MHz) Single Voltage Value |
1, 4 |
G1LV-0410 |
AC/DC Transfer Standard Calibration (10 Hz-1 MHz) Multiple Voltage Values |
1, 4 |
G1LV-0420 |
AC/DC Transfer Standard Calibration (1 MHz-100 MHz) Single Voltage Value |
1, 5 |
G1LV-0430 |
AC Measurement Standard Calibration |
1 |
G1LV-0431 |
AC Measurement Standard Calibration (included adjustment procedure) |
1 |
G1LV-0432 |
Wideband Option AC Measurement Standard Calibration (included adjustment procedure) |
1 |
G1LV-0433 |
Wideband Option AC Measurement Standard Calibration (included adjustment procedure) |
1 |
G1LV-0500 |
Oscilloscope Calibrator |
1 |
G1LV-0501 |
Oscilloscope Calibrator (included adjustment procedure) |
1 |
G1LV-0502 |
Oscilloscope Calibrator (9500B) |
1 |
G1LV-0503 |
Active Head |
1 |
G1LV-0515 |
Oscilloscope Calibration (600 MHz > BW< 6 GHz; Single Channel) |
|
G1LV-0516 |
Oscilloscope Calibration (600 MHz > BW < 6 GHz; Two Channels) |
|
G1LV-0517 |
Oscilloscope Calibration (600 MHz > BW < 6 GHz; Four Channels) |
|
G1LV-0620 |
Reference Voltage Divider Calibration |
1 |
G1LV-0630 |
Transconductance Amplifier Calibration (DCI < 20 A, ACI < 20 A) |
1 |
G1LV-0640 |
Transconductance Amplifier Calibration (DCI < 100 A, ACI < 100 A , 10 Hz - 100 kHz ) |
1 |
G1LV-9900 |
Special Calibration / Test |
2 |
(1) |
The service is in the acrreditation scope. |
(2) |
Price depends on the requirements. |
(3) |
|
(4) |
|
(5) |
|
(6) |
|
VOLUME DENSITY LABORATORY CALIBRATION / TEST LIST
CODE |
NAME |
NOTE |
G2HY-1100 |
Calibration of Piston Operated Pipette and Burette |
|
G2HY-1200 |
Calibration of volume vessels in the range of 0,1 mL - 5000 mL |
|
G2HY-1500 |
Calibration of metal volume vessels in the range of 2 L - 10 L |
1, 2 |
G2HY-1700 |
Calibration of metal volume vessels in the range of 20 L - 50 L |
1, 2 |
G2HY-1900 |
Calibration of metal volume vessels, 100 L |
1, 2,4 |
G2HY-2100 |
Calibration of metal volume vessels, 200 L |
1, 2,4 |
G2HY-2200 |
Calibration of metal volume vessels, 500 L |
1, 2, 4 |
G2HY-2300 |
Calibration of metal volume vessels, 1000 L |
1, 2, 4 |
G2HY-2400 |
Calibration of metal volume vessels, 2000 L |
1, 2, 4 |
G2HY-2500 |
Calibration of metal volume vessels, 5000 L |
1, 2, 4 |
G2HY-4100 |
Determination of reference liquid densities |
|
G2HY-4400 |
Calibration of hydrometers |
|
G2HY-4700 |
Calibration of digital density meter |
|
G2HY-9900 |
Special Calibration / Test |
3 |
(1) |
Calibration price is valid only for one scale. 25 % of the calibration price will be added to the total price for each additional scale. |
(2) |
In case of insufficient cleaning of your metal volume vessels, calibration service will not be available. |
(3) |
Price depends on the requirements. |
(4) |
The equipment must be delivered with the accessories necessary to discharge the calibration fluid (hoses, flanges, etc.). The customer is responsble for the transport and delivery of equipment to place of calibration and its removal. |
WATER & OTHER LIQUID FLOW LABORATORY CALIBRATION / TEST LIST
CODE |
NAME |
NOTE |
G2AS-2100 |
Water Flowmeter Calibrations between 0,3 kg/h-15 kg/h |
2,5,6,7 |
G2AS-2300 |
0,01-6 m3/h Water Flowmeter Calibrations |
1,2,5,6,7 |
G2AS-2500 |
0.3-30 m3/h Water Flowmeter Calibrations |
1,2,5,6,7 |
G2AS-2700 |
Water Flowmeter Calibrations upto 100 m3/h |
1,2,5,6,7 |
G2AS-2900 |
Water Flowmeter Calibrations upto 250 m3/h |
1,2,5,6,7 |
G2AS-3100 |
Water Flowmeter Calibrations upto 1000 m3/h |
1,2,5,6,7 |
G2AS-3300 |
Water Flowmeter Calibrations upto 2000 m3/h |
1,2,5,6,7 |
G2AS-4000 |
Tests for Liquid Armatures |
4,7 |
G2AS-4800 |
Water Flow Meters Verification Tests (for 3 flowrates) |
4,7 |
G2AS-4900 |
On-Site Calibrations |
3, 4, 8 |
G2AS-5000 |
Tests Explained in Water Flowmeter Type Approval Regulations |
4, 7 |
G2AS-5200 |
Vane Test |
4, 7 |
G2AS-5600 |
Pump Tests |
4, 7 |
G2AS-9900 |
Specific Liquid Flow Calibration / Tests |
4, 7 |
(1) |
Acredited item. |
(2) |
Calibration price changes by %50 if more then one meter output calibration is requested, if it is decided that device sent for calibration is not working properly, %50 of the normal price is requested, and if the device is not clean enough for calibration, %50 of the price will also be requsted for cleaning purposes from the customer. |
(3) |
On-Site calibration price is twice the price of calibration at UME and it may increase if there is any other needs for calibration on-site. Travelling expenses will be added to the price. |
(4) |
Price may change according to device type and test |
(5) |
Price increases by %50 for the requests of calibrations at temperatures other than standard laboratory conditions |
(6) |
Price increases by %50 for flow meter adjustment (i.e. K factor or similar) requests |
(7) |
In case of contamination of the flow measurement systems, lines and water due to the equipment sent to the calibration as dirty, the total cost of the water to be renovated, the work force spent on cleaning and the consumables used for cleaning are also taken from the customer. |
() |
Price increases by %50 for requests of calibrations of meters heavier than 40 kg (for 0-100 m3/h range) and heavier than 100 kg (for 100-2000 m3/h range). |
3-DIMENSION MEASUREMENTS (CO-ORDINATE METROLOGY) CALIBRATION / TEST LIST
CODE |
NAME |
NOTE |
G2BU-0100 |
Cylindrical Square (Roundness, Squareness, Straightness and Parallelism Measurements) |
1 |
G2BU-0110 |
Granite or Steel Square (Squareness Standard) |
1,2 |
G2BU-0200 |
Height Gauge |
1 |
G2BU-0210 |
Check Gauge (Calliper Checker) |
1,3 |
G2BU-0220 |
Riser Block |
1 |
G2BU-0400 |
Tapered Ring-Plug Gauges (calibration with CMM) |
1 |
G2BU-0410 |
Tapered Thread Ring-Plug Gauge (calibration with CMM) |
1 |
G2BU-0500 |
Plain Go-NoGo Ring-Plug Gauge (calibration with CMM) (for at least 10 pieces) |
1 |
G2BU-0510 |
Parallel Thread Go-NoGo Ring-Plug Gauge (calibration with CMM) (for at least 10 pieces) |
1 |
G2BU-0520 |
Snap Gauge Calibration (calibration with CMM) (for at least 10 pieces) |
1 |
G2BU-2100 |
Pin Gauge (Gauges for Aircraft Engines) |
4 |
G2BU-9900 |
Special Calibration / Test |
2 |
(1) |
Acredited Item. |
(2) |
Prices differ acc. to workpiece dimensions and number of measurement points. |
(3) |
The price of the check gauges longer than 600mm are re-evaluated |
(4) |
Price is calculated with the formula (2330+n*165) where n: Number of pins |
CALIBRATION / TEST LIST
CODE |
NAME |
NOTE |
G1TF-1000 |
Measurement of Thermal Conductivity by Guarded Hot Plate Method, 0,0015 W/m.K - 0,35 W/m.K (From 25 °C to 250 °C) |
1,2,3,4 |
G1TF-2000 |
Measurement of Thermal Conductivity by Heat Flow Method, 0.004 W/m.K - 2 W/m.K (From -20 °C to 90 °C) |
1,2,3,4 |
G1TF-3000 |
Measurement of Thermal Values by Differential Scanning Calorimetry (From -180 °C to 700 °C) |
1,2,3,4 |
G1TF-4000 |
Thermal Camera Radiometric Calibration (-50°C / 800 °C) |
2,3,5,6 |
G1TF-4100 |
Thermal Camera Radiometric Calibration (800°C / 1600 °C) |
2,3,5,6 |
G1TF-4200 |
Thermal Camera Radiometric Calibration (1600°C / 2300 °C) |
2,3,5,6 |
G1TF-4300 |
Thermal Camera Uniformity Measurement (-20°C / 50°C) (at 3 measurement points) |
1,2,3,6 |
G1TF-4400 |
Thermal Camera Uniformity Measurement (50°C / 100°C) (at 3 measurement points) |
1,2,3,6 |
G1TF-5000 |
IR Calibrators / Blackbody Surface Temperature Measurement |
1,2,3,7 |
G1TF-6000 |
IR Calibrators / Blackbody Emissivity Measurement |
1,2,3,8 |
G1TF-9900 |
Special Calibration / Test |
1,2,3,9 |
(1) |
|
(2) |
|
(3) |
|
(4) |
|
(5) |
|
(6) |
|
(7) |
|
(8) |
|
(9) |
|
CALIBRATION / TEST LIST
CODE |
NAME |
NOTE |
G1MM-1100 |
Calibration of Patient Simulator |
|
G1MM-1110 |
|
|
G1MM-1200 |
Calibration of NIBP Simulator |
|
G1MM-1210 |
|
|
G1MM-1220 |
|
|
G1MM-1300 |
Calibration of SpO2 Test Device |
|
G1MM-1320 |
Filter Media for Respirators |
|
G1MM-2100 |
Calibration of Electrical Safety Analyzer |
|
G1MM-3100 |
Calibration of Electro-surgery Analyzer |
|
G1MM-3200 |
Calibration of Defibrilator Calibrator |
|
G1MM-4100 |
Calibration of Gas Flow Analyzer |
|
G1MM-4200 |
|
|
G1MM-4300 |
|
|
G1MM-4400 |
|
|
G1MM-5100 |
Calibration of Infusion Pump Analyzer |
|
G1MM-6100 |
Ultrasonic Power Calibration |
|
G1MM-7100 |
Hearing Aid Acoustic Tests |
|
G1MM-8100 |
|
|
G1MM-8200 |
|
|
G1MM-8300 |
|
|
G1MM-8400 |
|
|
G1MM-8500 |
|
|
G1MM-9800 |
Special Ultrasound/Underwater Acoustical Measurements |
1 |
G1MM-9900 |
Special Calibration / Test |
1 |
(1) |
Pricing depends on scope of test/measurement |